1923 T-bucket Rat Rod Project on 2040-cars

Auto blog

Ford recalls 1.9m cars and crossovers for defective airbags

The Basics: Ford is recalling a total of 1,898,728 vehicles to replace defective Takata front passenger-side airbags. This includes the 2007-2010 Ford Edge, 2006-2011 Ford Fusion, 2005-2011 Ford Mustang, 2007-2011 Ford Ranger, 2007-2010 Lincoln MKX and 2006-2011 Lincoln MKZ, Zephyr and Mercury Milan vehicles built in North America. The Problem: The defective airbags have been linked to ruptures that can send metal fragments at the passenger, due to deteriorating propellant. Injuries/Deaths: Ford claims it's not aware of any injuries due to the problem, but rupturing Takata airbags have been linked to a series of serious injuries and deaths. The Fix: Dealers will replace the passenger-side frontal airbag at no charge to the customer. If you own one: Look out for a letter from the manufacturer to arrange service at your local dealer. If you'd like to check if your vehicle is affected, click on the safety recalls link on Ford.com and enter your VIN. Related Video:

Ex-PR chief Vines accuses Ford of bugging cars, phones

Jason Vines, former head of communications at Ford among other automakers, is accusing the Blue Oval of bugging his company phone and his car during the Firestone tire recall for the Explorer in 2001. The allegations have come to light in Vines' upcoming book What Did Jesus Drive? Crisis PR in Cars, Computers and Christianity.
According to The Detroit News, which has an advance copy of the book, Vines (pictured above) claims that after leaving the company, someone with security within Ford advised him that he had been bugged around the time of the recall. The allegations don't stop there, though. Vines further contends that he might not have been the only one to get this treatment, noting that then-general counsel John Rintamaki also believed he was being listened to.
According to The Detroit News, even if it had been a company phone, recording Vines without his knowledge still would have been a felony under Michigan law.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).