Dodge Other, page #9

Auto blog

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

Question of the Day: Most heinous act of badge engineering?

Badge engineering, in which one company slaps its emblems on another company's product and sells it, has a long history in the automotive industry. When Sears wanted to sell cars, a deal was made with Kaiser-Frazer and the Sears Allstate was born. Iranians wanted new cars in the 1960s, and the Rootes Group was happy to offer Hillman Hunters for sale as Iran Khodro Paykans. Sometimes, though, certain badge-engineered vehicles made sense only in the 26th hour of negotiations between companies. The Suzuki Equator, say, which was a puzzling rebadge job of the Nissan Frontier. How did that happen? My personal favorite what-the-heck-were-they-thinking example of badge engineering is the 1971-1973 Plymouth Cricket. Chrysler Europe, through its ownership of the Rootes Group, was able to ship over Hillman Avanger subcompacts for sale in the US market. This would have made sense... if Chrysler hadn't already been selling rebadged Mitsubishi Colt Galants (as Dodge Colts) and Simca 1100s as (Simca 1204s) in its American showrooms. Few bought the Cricket, despite its cheery ad campaign. So, what's the badge-engineered car you find most confounding? Chrysler Dodge Automakers Mitsubishi Nissan Suzuki Automotive History question of the day badge engineering question

Ford Mustang Shelby GT350R named Road & Track Performance Car of the Year

With a 526-horsepower, 5.2-liter V8 that roars to 8,250 rpm, it's really hard to consider the 2016 Ford Shelby Mustang GT350R an underdog in any fight. However, the Shelby held the lowest as-tested price and was only middle of the pack in terms of power in Road & Track's 2016 Performance Car of the Year challenge. The 'Stang's numbers clearly didn't tell the whole story about the potent coupe because Ford's muscle car grabbed the title in this year's test. A model needs to be new or significantly updated to be eligible for the honor, and R&T found an impressive slate of eight candidates this year. The challengers included the Bentley Continental GT3-R, Cadillac ATS-V Coupe, Chevrolet Corvette Z06, Dodge Viper ACR, Mercedes-AMG GT S, and Porsche Cayman GT4. The Ferrari 488 GTB was the most expensive of the bunch with an as-tested price of $347,942, which is five times more than the Shelby. Once the group was together, R&T hustled them over curving roads and on the National Corvette Museum Motorsports Park. There was a lot to love about the Shelby, even in this impressive crew. "With a flat-plane crank and Sport Cup 2 tires, the GT350R is a Mustang turned up to 11," editor-in-chief Larry Webster said in the announcement of the results. The GT350R joins some great company. Past winners include the Porsche 911 GT3 last year and the Corvette in 2013. For some fantastic photography and the complete appraisal of these performance machines check out R&T's website for the full story. Related Video: ROAD & TRACK NAMES THE FORD MUSTANG SHELBY GT350R THE 2016 PERFORMANCE CAR OF THE YEAR New York, NY (November 9, 2015) – Road & Track today named the Ford Mustang Shelby GT350R the 2016 Performance Car of the Year, beating out seven of the world's best new sports cars. The article appears in the December/January issue, on newsstands November 17, and on RoadandTrack.com. "With a flat-plane crank and Sport Cup 2 tires, the GT350R is a Mustang turned up to 11," said Larry Webster, editor-in-chief of Road & Track. "Not only does the car have soul and harness so much firepower with such ease, but the real achievement here is that it's so approachable. It's a car you can't help but love." The Mustang Shelby GT350R was the winner by a runaway vote.

Mopar highlights wild SEMA creations, AWD Challenger Concept

Thanks to 15,345 square feet of display area, FCA US' Mopar division certainly has ample space to display its parts and accessories at the SEMA Show. To lure attendees to check out all of those cars and components, the company is now revealing ten tuned vehicles for this year's aftermarket event. This isn't even the brand's whole fleet for the show, but it includes some major highlights for Dodge and Ram fans. A lack of traction traditionally makes rear-wheel-drive muscle cars dismal to drive when the weather gets slippery, but the Dodge Challenger GT AWD Concept (above) solves that age-old problem at SEMA. In addition to powering all four wheels through an eight-speed automatic, it boasts an angry-looking, wide-body kit with aggressively flared wheel arches. The asymmetrical stripe with Header Orange accents also adds some extra panache to the Destroyer Grey and Matte Black color scheme. The coupe can back up the macho look thanks to the Scat Pack 3 Performance Kit that adds 75 horsepower and 44 pound-feet of torque to the 5.7-liter V8. However, before you get too excited about driving one this winter, FCA US spokesperson Ariel Gavilan tells Autoblog: "It is only a concept." Mopar isn't done tuning Dodges for SEMA. The Charger Deep Stage 3 shows what's possible with the company's catalog by packing the Scat Pack 3, strut tower braces, coilover suspension kit, and bigger brakes. Meanwhile, the blacked-out Dart GLH Concept tries to harken back to the style of the famous Omni GLH by fitting a red-accented body kit, including a Mopar Performance aluminum hood. If the standard Ram 1500 Rebel is somehow too subdued, check out the Rebel X (right) in a vibrant shade called Copper. To be ready for anything offroad, it wears some muscular flares to fit 17-inch beadlock wheels and 35-inch Toyo tires. A concept, two-piece front skid plate protects the front. Drivers should also be comfortable no matter where they drive thanks to prototype Katzkin leather seats and a concept air-ride suspension. Chrysler enjoys some mods, as well. The 300 Super S has suave style with Matte Cerulean paint, concept 22-inch wheels, and a grille with little Mopar Ms dotted around it. Performance also sees a boost with a tuned engine, bigger brakes, and coilover kit. The gray 200 S Mopar is similarly stylish with a complete body kit, including a conceptual, dual-vented hood. Fiat and Ram's commercial models aren't left out of the SEMA fun, either.

Towing with the 2016 Ram lineup [w/video]

I do not tow things. Ever. Yet I recently found myself at the Fiat Chrysler Automobiles proving grounds in Chelsea, MI, where I'd be testing the hauling capabilities of Ram's current product range. This experience was not only a perfect education for a towing novice like me, but allowed me to tow far more weight than I'd ever consider hauling the real world, and all within the safe confines of the Chelsea Proving Grounds. There was an extremely diverse array of vehicles at my disposal, including Ram's gasoline- and diesel-powered offerings with trucks ranging from the 1500 on up through the 5500 Chassis Cab, as well ProMaster vans. Beyond that, FCA brought out a number of vintage Dodge pickups for me to play with, while also working with Case IH to provide a track-loader I could test. I put together a range of videos covering everything from the classics to the production trucks to the construction equipment. And despite some technical difficulties – you'll notice a distinct lack of in-car videos, with blame going to a corrupted micro SD card – I've assembled ten videos that give an up-close look at Ram's offerings. 2015 Ram ProMaster City Let's start small. The ProMaster City only has a towing capacity of 2,000 pounds. That's a reasonably impressive figure for a van that uses the same powertrain as a Chrysler 200. The 2.4-liter four-cylinder and nine-speed automatic weren't really bothered with the extra weight added by the trailer. Even when accelerating at freeway speeds, the ProMaster City didn't feel out of breath or hampered by its load. That said, the rear of the van was unloaded, which probably wouldn't be the case for most consumers. It's unclear how the City would feel if its driver were taking advantage of the max payload (1,883 pounds) and towing. 2015 Ram ProMaster 1500 To be polite, the Ram ProMaster is a difficult vehicle to like. Its awkward seating position is bus-like and lacks the visibility enjoyed by the Ford Transit or the utter driving comfort of the Mercedes-Benz Sprinter. Its 3.0-liter, four-cylinder turbodiesel engine, meanwhile, is something of an anomaly. While it's potent for a four-cylinder diesel, producing 295 pound-feet of torque and 174 horsepower, those numbers don't feel all that impressive when loaded down. The model I tested was barely using half of its 5,100-pound maximum towing weight and was loaded down with just 500 of its 3,620-pound payload. Yet it lacked the pluckiness of the smaller City.

Mopar teases four of 'nearly 20' SEMA Show concepts

Yesterday it was Chevrolet. Today, Mopar has dropped some SEMA knowledge, releasing a quartet of teaser images that give us some indication of what kind of cars, trucks, and crossovers Fiat, Chrysler, Dodge, Jeep, and Ram will be showing in Las Vegas. Like Chevy, Mopar's concepts utilize both production and concept accessories, although Fiat Chrysler has gone a bit more indepth on at least one of its concepts. Immediately, the most tantalizing teaser is the one shown above. Yes, that's the back of a Challenger, and aside from the bright orange accents on the gray body, you should take notice of the badge mounted on the spoiler – yes, that says "GT AWD." To be honest, such a vehicle wouldn't be a huge shock, as both the Challenger's LX platform-mates, the Dodge Charger and Chrysler 300, are offered with all-wheel-drive options. Still, adding such a vehicle to the production cycle would give Dodge a leg up on the rear-drive only Ford Mustang and Chevrolet Camaro. Aside from that concept, FCA has also released teasers of a Ram-based concept, a 300-based concept, and what we're guessing is a Fiat 500X. We can't wait to see what the actual Fiat concept has to do with kiteboarding. As for the 300 and Ram, there's not a lot of hints on what sort of styling details they'll contain. The Chrysler has additional LED accents and what we're guessing is matte blue paint, while the Ram is based on a Hemi-powered 1500 with Rebel styling cues. This is just a very tiny sample of Mopar's final SEMA roster, which include "hundreds" of parts. There should also be a total of 20 vehicles covering all four former Chrysler Group brands, as well as Fiat. Naturally, we'll have plenty to report on each vehicle once the SEMA show kicks off in the next couple weeks.

Dodge Viper might not live past 2017

The Dodge Viper might be running out of venom because the muscle-bound sports car could be on the road to being cancelled in just a few years. According to Allpar, the proposed deal between the United Auto Workers and FCA US would close the Connor Avenue Assembly plant, which produces the Viper, in 2017. The proposed union contract doesn't give a reason for closing the factory, but the decision is understandable if frustrating. The plant was idled twice last year to reduce production of the Viper to match flagging demand. A $15,000 price cut for the coupe eventually allowed for a sales surge, but that appetite hasn't continued in 2015. From January through September of this year, the company has only moved 503 of the sports cars, down eight percent. To further spur demand, Dodge has employed a few other tactics like the 1 of 1 program for buyers to personalize their Vipers, and the introduction of the brutally track-focused ACR. In a world where high-end sports cars are continuing to get friendlier for both their drivers and the environment, the Viper remains a holdout with a big, naturally aspirated V10. Even with the addition of some electronic aids on the latest Vipers, the snake still demands respect from those behind the wheel. Respect is fine, but sales are what matter to FCA – and the harsh reality is that a lack thereof might force the Viper into retirement, whether we like it or not.

Fiat brand chief reassigned then resigns amid flagging sales

Jason Stoicevich was replaced as head of the Fiat brand in North America just the other day. He was immediately reassigned to another job within Fiat Chrysler Automobiles. But according to Automotive News, Stoicevich quit the new job – and the company altogether – the very next day. The development comes amidst flagging sales for the Fiat brand in America. The introduction of the awkward-looking 500L multi-purpose vehicle has been largely regarded as a sales disaster in the US. Despite having just introduced the new 500X into the growing crossover market, and an overall upward trend across FCA group sales, the Fiat brand's figures have been dropping all year. While the Italian brand's volume has fluctuated from month to month compared to last year's sales, the number of cars its dealers sells on an average day has been firmly in decline. Fiat's downward trend reflects a general tendency in the market towards larger vehicles at the expense of smaller ones. However, the powers that be in Auburn Hills evidently felt that a change of leadership was in order, so it placed Dodge chief Tim Kuniskis in charge of all the company's mass-market passenger-car brands – namely Dodge, Chrysler, and Fiat – and moved Stoicevich to running the group's fleet and small-business operations. Stoicevich remained in charge of the company's California Business Center, but it seems as though he was as dissatisfied with the switch as his superiors were with the performance of the brand over which he presided, and so he apparently elected to step down and leave the company.

Leno recalls '90s showdown with Tim Allen and his mullet

Not many of us have buddies with garages full of classic cars, but that isn't the case for Jay Leno and Tim Allen. Of course, one of the advantages for two guys with such vast collections is occasionally getting to pit their cars against each other. The two comedians did just that in the mid-'90s with a burnout battle on The Tonight Show between Allen in a race-prepped Mustang and Leno in a drag racer. After some time away from regular television, Leno is returning to the airwaves with a Jay Leno's Garage series premiering on Oct. 7 (tonight) at 10:00 p.m. ET on CNBC. Let this clip serve as another taste of what to expect for the new TV show's mix of comedy and cars. After reminiscing about the old days in a gorgeous garage, the comedians get into two modern machines to reprise the classic challenge – after a little trash talk anyway. Don't worry because the YouTube series isn't going anywhere, though.

Legacy Classic Power Wagon First Drive

Shortly before the US entered World War II, Dodge supplied the military with a line of pickups internally codenamed WC, those letters designating the year 1941 and the half-ton payload rating. From 1941 to 1945 Dodge built more than a quarter million of them, and even though "WC" came to refer to the Weapons Carrier body style, the WC range served in 38 different configurations from pickup trucks to ambulances to six-wheeled personnel and weapons haulers. The story is that soldiers returning from active duty badgered Dodge for a civilian version of that indefatigable warhorse, so Dodge responded with the Power Wagon in 1946. Even for those no-nonsense times the truck was so austere that the first three names Dodge gave it were "Farm Utility Truck," "WDX General Purpose Truck," and "General Purpose, One Ton Truck." "Power Wagon" was the fourth choice, not finalized until just before it went on sale. Nothing like today's Power Wagon, the original could be seen as either a glorified tractor or a slightly less uncouth military vehicle – hell-for-leather meant going 50 miles per hour. But it would go nearly anywhere. The civilian version was still built like it had to survive, well, a world war; power take-offs (PTOs) ran all manner of ancillaries; multiplicative gear ratios helped it produce enough torque to make an earthquake envious. Said to be the first civilian 4x4 truck made in America, any organization that needed a simple, sturdy mechanized draught animal knew it needed a Power Wagon. If history, the aura of war, and ruthless functionality attract you but mean comforts and 70-year-old manners don't, then you need to get in touch with Legacy Classic Trucks. If that history, the aura of war, and the ruthless functionality attract you but the mean comforts and 70-year-old manners don't, then you need to get in touch with Legacy Classic Trucks. The Jackson Hole, WY, restorer retains every ounce of the Power Wagon's orchard-work aptitude, decorated with present-day amenities and the best components. Each job starts with having to find a usable donor. The city of Breckenridge, CO, bought the red truck in our gallery in 1947 and used it as a snowplow for the next 30 years. In 1977 a log-home builder bought it from the city and used it for another decade as a company hauler. That's the kind of grueling longevity that lets Ram put a five-figure premium on the 2500 Power Wagon pickup it sells today. Legacy Classics founder Winslow S.