~~~ Vw Camper Bus ~~~ Retro Vintage Runs And Drives on 2040-cars

Auto blog

Skoda unveils Volkswagen Up!-based Citigo

This is the all-new Skoda Citigo, and if you're thinking that it looks rather familiar, that's because its Volkswagen-badged kin recently debuted at the 2011 Frankfurt Motor Show. That's right, the long-rumored Skoda version of Volkswagen's new Up! city car has finally arrived.
Buyers will have a choice of two 1.0-liter three-cylinder engines - one with 59 horsepower, the other with a 74 hp and a blistering 106 mph top speed - both mated to a five-speed manual transmission. Powerful they are not, but these three-bangers should prove to be extremely efficient, with Skoda quoting fuel economy numbers of 62.8 and 60.1 miles per gallon, respectively (on the European cycle).
Being a Skoda, the Citigo will go on sale in its home market of the Czech Republic this fall, with the rest of Europe getting the car next summer. Follow the jump for Skoda's official release.

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.

VW readying new VR6 with forced induction

Volkswagen built a stonking, narrow-angle V6 in the 1980s and 1990s that was found in three different generations of the Golf (their performance iterations, obviously), three generations of the Passat, the New Beetle, the Corrado and the Touareg, among other VWs, a spate of Audis, Seats, a Skoda, and even the Porsche Cayenne. It was a sad day when it was announced that it'd be put out to pasture.
Rejoice, though, fans of the venerable VR6, because Volkswagen has a new, modern variant in the works that, according to AutoWeek, features direct injection and can easily be fitted with forced induction. In fact, AW mentions Volkswagen insiders that claim this unit will spawn a production version of the twin-turbo V6 shown on the Design Vision GTI from this year's Wörthersee festival. That unit produced an epic 503 horsepower and 413 pound-feet of torque.
Don't expect a production unit with that level of power (although it would make a hardy RS4 powerplant), though. In reality, AutoWeek is suspecting anywhere from 340 to 450 horsepower from the new mill. When it arrives at an undisclosed date in the future, it'll likely be found in the Passat and Passat CC as well as the production version of the CrossBlue.