2016 Toyota Sienna Le Wheelchair Accessible Mobility Van - 23,000 Az Miles! on 2040-cars

Auto blog

Junkyard Gem: 2004 Pontiac Vibe GT

The New United Motor Manufacturing plant in Fremont, California, built Toyota-derived machinery — badged as Toyotas, Chevrolets, Geos, and Pontiacs— from 1984 through 2010, and some of the very last vehicles that left the assembly line were Pontiac Vibes. The Vibe, sibling to the Toyota Matrix, mostly served as a ho-hum transportation appliance and/or fleet car, but a factory-hot-rod GT version could be purchased. Today's Junkyard Gem is one of those rare GTs, complete with the nearly unheard-of six-speed manual transmission, found in a self-service yard in northeastern Colorado. The regular Vibe had 123 or 130 horsepower, depending on the number of driven wheels, but the Vibe GT got the same 1.8-liter 2ZZ engine that went into the Celica GT-S. 180 horsepower, which was enough to make the 2,800-pound Vibe GT keep up with the 3,108-pound/215-horse Chrysler PT Cruiser Turbo that year. Sadly, no race series pitting Vibe GTs against PT Cruiser Turbos and Chevy HHR SSs on road courses ever materializedÂ… but it's not too late. The Vibe GT has something you couldn't get in a PT Cruiser or Chevy HHR, though: a six-speed manual transmission as standard equipment. In fact, the six-speed was the only transmission offered in the early Vibe GTs (an automatic became an option later on). You'll find plenty of three-pedal econoboxes from this era, because they were significantly cheaper than their slushbox-equipped counterparts, but the Vibe GT had plenty of competition from sportier-looking cars with manual transmissions in 2004. Not many were sold. This car is covered with nasty dents from golf-ball-sized hail (all too common in High Plains Colorado), so it may have been an insurance total that nobody wanted at auction. Sold in Wyoming, will be crushed in an adjacent state. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Fuel for the soul. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. The kids, they were crazy about the Vibe (well, maybe not). This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Toyota had right-hand-drive Matrixes brought over to Japan from Canada, but a NUMMI-built version of the Vibe could be purchased there for a few years as well. This was the Voltz, and its advertising seems notably frantic even by the standards of Japanese car commercials.

Scion was slain by Toyota, not the Great Recession

Scion didn't have to go down like this. Through the magic of hindsight and hubris, it's easier to see what went wrong. And what might have been. What the industry should understand is this: Scion wasn't a losing proposition from the get-go. Its death is due to negligence and apathy. This is more than just the failure of a sub-brand. It's the failure of a company to deliver new and compelling products over an extended period of time. Toyota will point to the Great Recession as the reason it hedged its bets and withdrew funding for new vehicles, instead of using that as an opportunity to redouble efforts. This was as good as a death warrant, although myopically no one realized it at the time. Sadly, GM's Saturn experiment was a road map for this exact form of failure. No one at Toyota seemed to think the Saturn experience was worth protecting their experimental brand from. Or they weren't heard. Brands live and die on product. Somehow, Scion convinced itself that its real success metric was a youthful demographic of buyers. It seems like this was used to gauge the overall health of the brand. Look at the aging and uncompetitive tC, which Scion proudly noted had a 29-year-old average buyer. That fails to take into account its lack of curb appeal and flagging sales. Who cares if the declining number of people buying your cars are younger? Toyota is going to kill the tC thirteen years [And two indifferent generations ... - Ed.] after it was introduced. In that time, Honda has come out with three entirely new generations of the Civic. Scion wasn't a losing proposition from the get-go. Its death is due to negligence and apathy. At launch, the brand could have gone a few different ways. The xB was plucky, interesting, and useful – a tough mix of ephemeral characteristics – but the xA didn't offer much except a thin veneer of self-consciously applied attitude. That's ok; it was cute. Enter the tC, which managed to combine sporty pretensions with decent cost. It took on the Civic Coupe in the contest for coolness, and usually managed to win. More importantly, an explicit brand value early on was a desire to avoid second generations of any of its models, promising a continually evolving and fresh lineup. At this point, the road splits. Down one lane lies the Scion that could have been. After a short but reasonable product lifecycle, it would have renewed the entire lineup.

Tougher than steel: Wood pulp could make lighter auto parts

KYOTO, Japan — The global push among carmakers to make ever lighter vehicles is leading some auto suppliers in Japan to turn to what seems like an unlikely steel substitute — wood pulp. Japanese researchers and auto component makers say a material made from wood pulp weighs just one-fifth of steel and can be five times stronger. The material - cellulose nanofibers — could become a viable alternative to steel in the decades ahead, they say, although it faces competition from carbon-based materials, and remains a long way from being commercially viable.> Related: Jay Leno drives the Renew cannabis car — hemp you can't dent Reducing the weight of a vehicle will be critical as manufacturers move to bring electric cars into the mainstream. Batteries are an expensive but vital component, so a reduction in car weight will mean fewer batteries will be needed to power the vehicle, saving on costs. "Lightweighting is a constant issue for us," said Masanori Matsushiro, a project manager overseeing body design at Toyota. "But we also have to resolve the issue of high manufacturing costs before we see an increased use of new, lighter-weight materials in mass-volume cars."A NEW PROCESS Researchers at Kyoto University and major parts suppliers such as Denso Corp, Toyota's biggest supplier, and DaikyoNishikawa Corp, are working with plastics incorporated with cellulose nanofibers — made by breaking down wood pulp fibers into several hundredths of a micron (one thousandth of a millimeter). Cellulose nanofibers have been used in a variety of products ranging from ink to transparent displays, but their potential use in cars has been enabled by the "Kyoto Process," under which chemically treated wood fibers are kneaded into plastics while simultaneously being broken down into nanofibers, slashing the cost of production to roughly one-fifth that of other processes. "This is the lowest-cost, highest-performance application for cellulose nanofibers, and that's why we're focusing on its use in auto and aircraft parts," Kyoto University Professor Hiroaki Yano, who is leading the research, told Reuters in an interview. The university, along with auto parts suppliers, are currently developing a prototype car using cellulose nanofiber-based parts to be completed in 2020.