Find or Sell Used Cars, Trucks, and SUVs in USA

1994 Toyota Land Cruiser Base Sport Utility 4-door 4.5l on 2040-cars

US $4,000.00
Year:1994 Mileage:305857
Location:

Fremont, California, United States

Fremont, California, United States
Advertising:

 I bought this truck with a misfire on cylinder # 1 after burning one exhaust valve.

work done.

Complete Valve job, tune up, Replace ignition wires, spark plugs, distributor cap and rotor, fuel filter, air filter, upper and lower radiator hose heater valve and all the hoses,

I also test piston rings before valve job  there holding very good.

Truck has new tires 95%

New front and rear brake pad and rotors.

Tow pakage

This truck runs Great Suspention is very good condition it has no leaks super clean interior it will need paint job on the silver part but  no dents or dings

All this truck need is paint job




Auto Services in California

Zip Auto Glass Repair ★★★★★

Auto Repair & Service, Windshield Repair, Glass-Auto, Plate, Window, Etc
Address: 2549 Marconi Ave, Rncho-Cordova
Phone: (877) 890-9370

Z D Motorsports ★★★★★

Auto Repair & Service, Automobile Body Repairing & Painting
Address: 8115 Canoga Ave, Calabasas-Hills
Phone: (818) 932-9222

Young Automotive ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Auto Transmission
Address: 890 Central Ave, Permanente
Phone: (650) 969-1151

XACT WINDOW TINTING & 3M CLEAR BRA PAINT PROTECTION ★★★★★

Auto Repair & Service, Glass Coating & Tinting Materials, Window Tinting
Address: 5140 E Airport Dr Suite G, Montclair
Phone: (909) 605-0422

Woodland Hills Honda ★★★★★

New Car Dealers
Address: 6111 Topanga Canyon Blvd, Bell-Canyon
Phone: (818) 887-7111

West Valley Machine Shop ★★★★★

Auto Repair & Service, Automobile Machine Shop, Engine Rebuilding & Exchange
Address: 9811 Deering Ave, Val-Verde
Phone: (818) 998-5084

Auto blog

Toyota to recall 185k cars globally, including Yaris

Thu, 04 Jul 2013

Toyota has announced it is recalling a total of 185,000 vehicles worldwide for a power steering issue. Yaris and (overseas) Vitz models built between November 2010 and March 2012 could suffer a short circuit in their power steering control module if water gets inside. Should that happen, the power steering could fail, increasing effort when turning. The recall also includes the Verso-S and Ractis built from August 2010 to August 2011. The recall covers 130,000 vehicles in Japan and around 22,450 in Europe.
Only 74 units are being recalled in the United States.
Toyota says if the fault occurs, the vehicle will display the Electronic Power Steering warning light on the dash and a buzzer will sound. The automaker will alert owners by mail and dealers will replace the power steering control module free of charge. You can read the quick press release on the recall below for more information.

Toyota restructuring US operations, possibly moving to Texas

Sun, 27 Apr 2014

According to multiple sources familiar with the matter, Toyota is poised to announce Monday that it is restructuring its US operations, which may include plans to relocate some of its operations to Texas. Toyota Motor Sales has been located in California since 1957, and is responsible for North American sales, marketing, and distribution for Toyota, Lexus and Scion. According to Toyota literature, its Torrance operations presently employs 6,156 workers and represents a $2.3-billion investment.
Workers in Toyota's Torrance offices were abuzz about the possible relocation to Texas. One young offspring of a Toyota employee even posted to Twitter that her parents warned about the upcoming move, and she said she's refusing to go.
Rumors at one point had Toyota settling in Richardson, TX, just outside Plano. But Autoblog talked to Richardson Mayor Laura Maczka, who said she would be thrilled if that were true, but has not heard anything on the subject. Autoblog also emailed with Bill Sutherland, a city councilman in Torrance, CA, who said, "To date the only info I have is what I have read in the paper expecting a press release Monday."

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Thu, Sep 11 2014

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.