2008 Toyota Limited on 2040-cars

Auto blog

Toyota will bring Lexus-based Platform 3.0 autonomous vehicle to CES

The Toyota Research Institute says it will bring its next-generation Platform 3.0 automated driving vehicle to CES next week, an autonomous test car that is notable for incorporating the sensors and cameras into the body, rather than as ungainly attachments, and with the spinning LIDAR rooftop sensor replaced by a more sleek panel of sensors. Platform 3.0 is built on a Lexus LS600hL. Toyota Research Institute says it enlisted CALTY Design Research in Ann Arbor, Mich. and engineers at Toyota's nearby North America R&D center to conceal the equipment. As a result, Platform 3.0 gets a new rooftop weather and temperature proof panel, which it says was inspired by off-road motorcycle helmets, integrated into the available space in the sunroof compartment to minimize height. It's also embellished with chrome trim along the side, where it meets the roofline, and the rear swoops down to integrate with the LS's contour lines. The team also managed to consolidate computational electronics and wiring into a small box in the trunk. Toyota says the Platform 3.0 is one of the most perceptive autonomous test vehicles on the road today, with a design makes the test vehicle easy to build at scale. It gets a Luminar LIDAR system boasting a 200-meter, 360-degree range (the previous version only tracked the forward direction), enabled by four high-res LIDAR scanning heads that help it better see dark objects. Shorter-range LIDAR sensors feature low on all four sides of the vehicle, one on each front quarter panel and on the front and rear bumpers, to detect low-level and smaller objects, like children or road debris. Production begins this spring at the Toyota Motor North America R&D headquarters at low volumes to allow for flexibility, given the rapid rate of development of Toyota's autonomous test platforms. Some will be assembled using Toyota's Guardian dual-cockpit control layout to allow for transferring control between a human test driver and the automated system while keeping the driver as a backup, while the single-cockpit, fully autonomous Chauffeur mode will be shown at CES starting Jan. 9.Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Least favorite vehicles of 2017

IIHS: Drivers safer than passengers in frontal crash test

The Insurance Institute for Highway Safety introduced a small overlap frontal crash test in 2012 that replicates what happens when the front corner of a car impacts another object. In the test, vehicles travel at a speed of 40 mph toward a five-foot-tall barrier with 25 percent of the total width of the car striking the barrier on the driver side. One would assume that vehicles with good small overlap front ratings would protect the driver and the passenger equally. But a recent study from the IIHS proves that passengers aren't as protected as drivers. The IIHS conducted the test on seven small SUVs with good driver-side small overlap ratings and only one of the vehicles, the 2016 Hyundai Tucson, performed well enough to be given a good rating. The other SUVs performance ranged from poor to acceptable. After reviewing the results of the test, the IIHS is deliberating whether it should institute a passenger-side rating as part of its Top Safety Pick criteria. "This is an important aspect of occupant protection that needs more attention," states Becky Mueller, lead author of the study and an IIHS senior research engineer. "More than 1,600 right-front passengers died in frontal crashes in 2014." Since the small overlap front test was introduced, 13 automakers have made structural changes to 97 vehicles with roughly three-quarters earning a good rating after the adjustments. The IIHS' test for frontal ratings is completed with a dummy in the driver's seat and with a barrier overlapping the driver's side. Which makes sense, as passengers aren't always riding in a vehicle. "It's not surprising that automakers would focus their initial efforts to improve small overlap protection on the side of the vehicle that we conduct the tests on," states David Zuby, IIHS executive vice president and chief research officer. "In fact, we encouraged them to do that in the short term if it mean they could quickly make driver-side improvements to more vehicles. As time goes by, though, we would hope they ensure similar levels of protection on both sides." As the IIHS' test revealed, there's a massive difference in safety between the two front seats. Increase passenger safety, according to Mueller, would require automakers to strengthen the occupant compartment by using a different type of material or by making it thicker.

Toyota Camry, Lexus RX to get aluminum parts

Ah, aluminum. The lightweight, strong material has long held a following within the premium ranks, but as Ford prepares to launch an aluminum F-150, the material is gaining acceptance among more mainstream automakers. Toyota is one such brand, with a new report indicating that the Japanese giant will add aluminum bits and bobs to some of its upcoming vehicles.
These won't be full, aluminum-intensive treatments like the F-150, however. Automotive News reports that an aluminum hood and liftgate will be coming to the 2016 Lexus RX, and following that, the Camry will get a bonnet built from Element 13 for model year 2018.
As AN points out, Toyota is no stranger to aluminum, using it in Japanese-built models like the Prius and Scion FR-S. The RX and Camry, though, will mark the first time the company's North American factories will use the material, and they'll do so on a significantly larger scale, owing to the higher volumes that the Camry and RX represent.