Dodge Ram Drw 6-speed Manual Spray Liner Clean Satellite Cruise Power Seat on 2040-cars

Auto blog

A beginner's guide to plowing snow with a heavy-duty truck

I live in a desert, so the only things getting plowed around here are mud flows and brewer neighbors. But I enjoy machinery and haven't plowed any snow since a "loaded" truck meant one with A/C and a CD player, so I jumped at the chance for a plow primer in a Ram HD on a Canadian airfield. Running a plow is like welding – the basics come quickly but experience pays dividends. The first thing to deal with is a frequently changing horizon because, stout as they are, even three-quarter-ton heavy-duty trucks will move up and down in front considerably with a 600-to-800-pound plow hanging off, and fast plow hydraulics rival some low-riders for bounce effect. Getting going is easy unless you forgot blocks and the plow froze to the ground, rookie. If you have to drive to your plowing assignment, blade height needs some experimentation to find the best cooling airflow; if you think sub-freezing temperatures negate that concern, remember you've installed what amounts to a 20-square-foot air brake up front that the truck has to overcome, and blowing snow could block some cooling air passages. Whether it's a "straight" blade or V design, always have it tilted to the right lest you catch a hidden post, solid mailbox, or edge of a snow bank. Most plow operators I spoke to rarely exceed 45 mph in transit because of cooling, front suspension travel, and common sense, and you should go even slower if you don't have some ballast like chains, extra fuel tanks, or a salt spreader to balance the load on the back. With trucks' relatively slow steering and all that weight up high, oversteer is best avoided. With a little clean space to get a run, stick it in Drive to gather momentum and lower the plow simultaneously to float, where the weight of the plow rests on and lets it run along the surface. Momentum is good until you hit something you didn't know about, at which point the plow's breakaway systems limit damage but your truck could still hit something big; caution never hurts. Start out at 10 to 15 mph, depending on consistency and depth, making a clean wave off one side. If you have to push it straight, as you slow coincidentally raise the blade at the bottom of the pile to shove it up higher. Carry too much speed here and you'll stop with an unceremonious thud. Common mistakes cited among a few experts were people pushing banks of snow rather than plowing it, and rushing the shift between Drive and Reverse, throttling up before the shift is completed.

Cummins builds 2-millionth diesel for Ram

Ahead of a new Ram Heavy Duty that will debut sometime next year (check out the spy shots below), Chrysler and Cummins are celebrating a milestone in a 24-year partnership that has supplied the Ram pickup with diesel engines.
In its early years, the Cummins straight-six turbo diesel was rated at just 160 horsepower and 400 pound-feet of torque, and its clattering 12 valves could be heard from a mile away. Its most recent configuration still uses a straight-six layout, but displacement grew to 6.7 liters in 2007 allowing the engine to now produce up to 385 hp and a whopping 850 lb-ft of torque. While a rumored smaller Cummins engine for use in the light-duty Ram 1500 never materialized, the work-ready 6.7-liter Cummins turbo diesel accounts for 80 percent of all Ram HD sales.
Chrysler has not yet announced when and where this two-millionth engine will be on display, but you can read more about the engine and the partnership in the press release below.

FCA recalling 323,000 cars for wiring, software issues

The Basics: Fiat Chrysler Automobiles (FCA) is conducting a voluntary recall for an estimated 323,361 cars in the US. The affected vehicles were built after September 23, 2014 and include: the 2015 Chrysler 200, Ram ProMaster City, Jeep Renegade, and 2014 and 2015 Jeep Cherokees. The Problem: An insufficient crimp in the vehicles' wiring harness may result in a solenoid fault code, which could cause the engine to stop. The loss of power could lead to an accident. Injuries/Deaths: None reported. The Fix: FCA will update the affected vehicles' software and replace wire harnesses, as needed. According to FCA, owners that experience the problem can temporarily resolve the issue by restarting the vehicle. If you own one: FCA is reaching out to owners to schedule a service. Related Video: Statement: Wire Harness Crimp July 22, 2016 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 323,361 vehicles in the U.S. to update certain software and replace wire harnesses, as needed. An examination of warranty data led to an FCA US investigation that discovered an insufficient crimp in a wire harness. Such a crimp may lead to a solenoid fault code that can cause propulsion loss. The Company is unaware of any related injuries or accidents. Most vehicles in the recall population will not experience this fault code over their lifetimes. However, should the condition occur, it can typically be temporarily resolved by stopping the vehicle and re-starting its engine. Accordingly, FCA US urges customers to heed the instructions on their recall notices. Affected are certain model-year 2015 Chrysler 200 midsize sedans, Ram ProMaster City small vans, Jeep Renegade and Cherokee SUVs. Certain model-year 2014 Cherokees are also affected. A change made in the harness-manufacturing process eliminates the need to recall any vehicle built after Sept. 23, 2014. An estimated 35,511 additional vehicles in Canada are included in the campaign; as are 7,067 in Mexico; and 43,927 outside the NAFTA region. Customers will be advised when they may schedule service. Those with questions may call the FCA US Customer Care Center at 1-800-853-1403. News Source: FCAImage Credit: AOL Recalls Chrysler Jeep RAM FCA jeep renegade ram promaster city