2014 Ram 3500 Slt on 2040-cars

Auto blog

A beginner's guide to plowing snow with a heavy-duty truck

I live in a desert, so the only things getting plowed around here are mud flows and brewer neighbors. But I enjoy machinery and haven't plowed any snow since a "loaded" truck meant one with A/C and a CD player, so I jumped at the chance for a plow primer in a Ram HD on a Canadian airfield. Running a plow is like welding – the basics come quickly but experience pays dividends. The first thing to deal with is a frequently changing horizon because, stout as they are, even three-quarter-ton heavy-duty trucks will move up and down in front considerably with a 600-to-800-pound plow hanging off, and fast plow hydraulics rival some low-riders for bounce effect. Getting going is easy unless you forgot blocks and the plow froze to the ground, rookie. If you have to drive to your plowing assignment, blade height needs some experimentation to find the best cooling airflow; if you think sub-freezing temperatures negate that concern, remember you've installed what amounts to a 20-square-foot air brake up front that the truck has to overcome, and blowing snow could block some cooling air passages. Whether it's a "straight" blade or V design, always have it tilted to the right lest you catch a hidden post, solid mailbox, or edge of a snow bank. Most plow operators I spoke to rarely exceed 45 mph in transit because of cooling, front suspension travel, and common sense, and you should go even slower if you don't have some ballast like chains, extra fuel tanks, or a salt spreader to balance the load on the back. With trucks' relatively slow steering and all that weight up high, oversteer is best avoided. With a little clean space to get a run, stick it in Drive to gather momentum and lower the plow simultaneously to float, where the weight of the plow rests on and lets it run along the surface. Momentum is good until you hit something you didn't know about, at which point the plow's breakaway systems limit damage but your truck could still hit something big; caution never hurts. Start out at 10 to 15 mph, depending on consistency and depth, making a clean wave off one side. If you have to push it straight, as you slow coincidentally raise the blade at the bottom of the pile to shove it up higher. Carry too much speed here and you'll stop with an unceremonious thud. Common mistakes cited among a few experts were people pushing banks of snow rather than plowing it, and rushing the shift between Drive and Reverse, throttling up before the shift is completed.

2019 Ram 1500 Tradesman shows off its simple lights

Each time a spy photographer has caught the 2019 Ram 1500 pickup running around, it's always had the same style of lights and grilles. This time, one of our photographers caught two Rams that have noticeably different versions of those body parts. The first one shown above has the same grille we've already seen. The difference is that the flashy LED-accented headlights are gone. Instead, it uses much simpler, more conventional reflector-style headlights. That doesn't mean Ram hasn't taken the time to give them a little flair, though. The lamps are divided such that the upper element lines up with the upper portion of the grille, and the lower portion with the grille bars and lower opening. The taillights are much simpler, too, also using a reflector setup and very clear lenses. These plain headlights lead us to believe that this is a base-model 1500 Tradesman. The second Ram shown has its lights well-covered, but the grille is exposed, and it's also different from past prototypes. It has a wavy mesh pattern in the grille openings rather than slats. The crossbar design remains, though. This different grille also confirms that Ram will offer appearance variations to distinguish models. We're not sure if this is a higher-level or lower-level trim, though. We would have a better idea if we could see the lights. All our questions should be answered soon, since the new Ram 1500 will be fully revealed next week at the Detroit Auto Show. Then we'll see all the grilles and headlights and their associated trims as they were meant to be. Related Video:

GM being sued over imploding Bosch fuel pumps in Duramax diesel trucks

Texas-based law firm Hilliard Martinez Gonzalez (HMG) this week filed a class-action lawsuit against General Motors over an alleged issue with Bosch CP4 fuel pumps. The suit claims Bosch designed the CP4 pump to work with European diesel fuel, which is thicker than U.S. diesel. When GM installed that pump in the 6.6-liter Duramax engine used from the 2011 to 2016 model years, the lawsuit claims the thinner U.S. fuel didn't provide enough lubrication, allowing air pockets to form in the fuel pump. That, in turn, allegedly let metal rub against metal inside the pump, causing the pump to eventually disintegrate and "send thousands of metal shards into the fuel injection system and every part of the engine." The Detroit News reported on the most recent lawsuit filed in Michigan's Eastern District Court, but the case is another piece of nationwide legal maneuvering going on since at least last September. Every U.S. truck maker used the Bosch CP4 fuel pump, and HMG originally went after all of them, as well as Bosch. On September 30, 2018, HMG filed a class-action suit in Texas on behalf of eight plaintiffs. The law firm wanted to prosecute the affair under RICO — the Racketeer Influenced and Corrupt Organizations Act — and named 10 defendants: FCA US LLC, FCA North America Holdings, LLC, F/K/A Chrysler Group, Fiat Chrysler Automobiles, N.V., Ford Motor Company, General Motors LLC, Robert Bosch GmbH, Robert Bosch LLC, VM North America, Inc., and VM Motori S.P.A.  The firm filed another suit in Florida on Nov. 2, 2018, against the same 10 defendants, again under the RICO statute, this time on behalf of more than 30 plaintiffs. We don't know how many other suits might have been filed, but the two suits mentioned apparently didn't have legs — the courts dismissed both quickly. So HMG shifted its strategy away from the RICO angle, and focused its efforts on GM, filing suit in California on Nov. 20, 2018. Instead of trying to catch 10 fish with a small net, HMG wants to score one fish with a big net. The results have borne more promise for the plaintiffs. In July this year, a judge in California denied GM's motion to dismiss, noting "the alleged defect is central to the vehicleÂ’s function." This latest suit filed on Aug. 6 in Detroit singles out GM again.  The Bosch CP4 is known to be problematic, however.