2023 Ram 2500 Big Horn Crew Cab 4x4 8' Box on 2040-cars

Auto blog

Ram considering Rumble Bee concept for production

Yellow truck enthusiasts, take note - Ram is considering production for its Rumble Bee Concept, a very, very extroverted pickup that debuted at the 2013 Woodward Dream Cruise. Drawing inspiration from the last Ram Rumble Bee, which in turn borrowed heavily from the Dodge Super Bee muscle cars of the 1960s, the Rumble Bee sports a few things that set it apart from the standard 1500 lineup.
The most obvious change is its retina-scorching, matte yellow paint. Teamed up with a two-inch suspension drop and monster 24-inch black wheels wrapped in low-profile tires, the Rumble Bee cuts an imposing figure. Matching that aggressive exterior is a 5.7-liter Hemi V8, complete with 395 horsepower and an exhaust system that can go from raucous and muscle-car-like to the full-on NASCAR at the push of a button.
According to Edmunds, after a positive reception at the Dream Cruise, the Auburn Hills automaker is now presenting the truck to dealers in a bid to gauge interest. "We try to listen to the dealers. They know their marketplace," Ram's Dave Sowers tells Edmunds, adding that Ram could produce the new truck.

Ram flubs ProMaster cargo capacity

The Ram ProMaster is going to look a little smaller on the inside, at least by way of its specification sheets, despite the sheet metal staying the same.
When Ram originally published the cargo capacity for its van, it simply did a direct conversion from the European rating of 15 cubic meters to 530 cubic feet. However, that didn't take into account the standard way internal measurements are calculated for the US. While the trucks have been on sale since October, the automaker just noticed the problem, and it's working on a revised figure. According to Automotive News, the new carrying ability for the ProMaster is likely between 450 and 475 cubic feet.
The difference stems from two standards for measuring capacity. In Europe, the entire internal area is determined and then obstacles like seats are subtracted from it. That means areas where freight could never go, like on top of seat backs, gets included in the figure. In the US, only the area where goods could actually fit is included, which leads to lower specs with no actual change in space.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.