1967 Blue Sprint! 3 Speed Manual Transmission Runs & Drives Body Panels Rare Car on 2040-cars

Auto blog

GM recalls 61k more vehicles in three campaigns

Following a stop-delivery order for its new midsize trucks and a rash of recent recalls, General Motors is issuing three more campaigns covering 60,575 vehicles in North America with 57,182 of them in the US. As of October 1, the automaker has issued a total of 74 recalls (see the ridiculously long chart to the right) this year covering 26,495,070 units in the US.
The largest campaign covers 46,873 examples in the US of the 2008-2009 Pontiac G8 and 2011-2013 Chevrolet Caprice Police Patrol Vehicle imported from Australia. It's possible for the driver's knee to hit the key and make it move from the "Run" to "ACC" position while driving. GM says its Holden division is developing a fixed-blade key that's supposed to fix the problem by only allowing it to rotate toward the "On" position. There has been one crash caused by this fault but no injuries or fatalities.
The second recall is for 10,005 units of the 2004-2007 Cadillac CTS-V and 2006-2007 Cadillac STS-V because "the fuel pump module electrical terminal may overheat." This can cause a flange to melt and allow the pump to leak fuel. GM specifies that the remedy for the CTS-V is replacing the fuel module and fuel tank jumper harness, but it doesn't specify how the STS-V is being repaired.

2008-2009 Pontiac G8 recalled over airbag concern

General Motors is recalling around 38,000 Pontiac G8 sedans from its 2008 and 2009 model years. The National Highway Traffic Safety Administration reports that the cars may have a passenger-side airbag flaw that might prevent proper deployment in certain scenarios.
According to NHTSA, the airbag might not adequately protect a fifth percentile woman - that is, a woman around four-foot, 11-inches weighing 108 pounds. The New York Times indicates that the anomaly was found during a crash test conducted by GM's Australian branch, Holden, which was testing the G8's twin (read: Commodore) for head injuries. According to that report, the test in question is specifically tailored to simulate injuries to females, so the results do not apply to men or children.
The issue has been blamed on a seat position sensor that governs airbag deployment rates. NHTSA indicates that when the front passenger seat is moved all the way forward, the faulty sensor may inappropriately trigger a 30-millisecond delay between airbag stages, potentially leading to greater injuries.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...