1968 Pontiac Gto "judge Tribute" Phs Certified, Full Body Off Restoration!!!!!!! on 2040-cars

Auto blog

Junkyard Gem: 2010 Pontiac Vibe

Just over a month before filing for Chapter 11 bankruptcy in June 2009, General Motors announced that the 83-year-old Pontiac Division would be "phased out" by the end of 2010. Only three Pontiac vehicles were sold as 2010 models in the United States: the Solstice, Vibe and G6 (new G3s were sold here during 2010 but they were all 2009 models, while the G5 was available as a 2010 model only in Canada and Mexico). Today's bit of junkyard automotive history is one of the very last Vibes ever built, found in a yard near Denver, Colorado. This car is significant not just as one of the final vehicles to bear Pontiac badges but also as one of the last cars built by the New United Motor Manufacturing Incorporated GM-Toyota joint venture in California, better known as NUMMI. The NUMMI factory began life as GM's Fremont Assembly, which built its first vehicle (a C-Series pickup) in 1963 and closed in 1982 after building its final vehicle (an Oldsmobile Cutlass Ciera). Rebooted as NUMMI, the first 1985 Chevrolet Nova (an Americanized AE82 Toyota Corolla Sprinter) rolled off the line in December of 1984. A quarter-century and better than eight million vehicles hence, NUMMI shut down production after its last Corolla was finished on April 1, 2010. While there was some noise about the Oakland Athletics building a new stadium on the site at the time, Tesla ended up buying most of the site soon after that. Tesla now builds more vehicles per year there than NUMMI ever did. The Vibe was co-developed with Toyota and based on the same platform as the ninth-generation Corolla. The Toyota Matrix was mechanically identical and was built in Canada, while the Japanese-market version (known as the Toyota Voltz) was built on the same NUMMI line as the Vibe and shipped across the Pacific. The Vibe/Matrix/Voltz got a redesign for the 2009 model year, but few noticed due to all the turmoil in the GM world at the time. The final Vibe was built in August 2009. This car was built in July of 2009, just before the end. It was living in West Texas just prior to coming to Colorado. El Paso is about a ten-hour drive from this car's current location. Once in the Centennial State, it got parked somewhere it shouldn't have been and ended up being auctioned to Pick Your Part. An occupant of this Vibe had time to sample some of the local agricultural products before that happened.

GM recalls 61k more vehicles in three campaigns

Following a stop-delivery order for its new midsize trucks and a rash of recent recalls, General Motors is issuing three more campaigns covering 60,575 vehicles in North America with 57,182 of them in the US. As of October 1, the automaker has issued a total of 74 recalls (see the ridiculously long chart to the right) this year covering 26,495,070 units in the US.
The largest campaign covers 46,873 examples in the US of the 2008-2009 Pontiac G8 and 2011-2013 Chevrolet Caprice Police Patrol Vehicle imported from Australia. It's possible for the driver's knee to hit the key and make it move from the "Run" to "ACC" position while driving. GM says its Holden division is developing a fixed-blade key that's supposed to fix the problem by only allowing it to rotate toward the "On" position. There has been one crash caused by this fault but no injuries or fatalities.
The second recall is for 10,005 units of the 2004-2007 Cadillac CTS-V and 2006-2007 Cadillac STS-V because "the fuel pump module electrical terminal may overheat." This can cause a flange to melt and allow the pump to leak fuel. GM specifies that the remedy for the CTS-V is replacing the fuel module and fuel tank jumper harness, but it doesn't specify how the STS-V is being repaired.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...