1999 Pontiac Grand Am Se Coupe 2-door 3.4l on 2040-cars

Auto blog

Rumormill: DeLorean Motor Company considering rescuing Pontiac Solstice?

DeLorean Motor Company Pontiac Solstice renderings - Click above for high-res image gallery
General Motors has made a science out of sharing platforms. So when the company's Kappa platform was introduced for a new rear-drive roadster to be distributed across three different motor divisions, you'd have figured the program was pretty safe, right? Unfortunately for the workers at the Wilmington Assembly Plant which manufactured the Kappa roadsters, those three divisions were Pontiac, Saturn and Opel - three units which the General has either sold or shut down. Which is a shame, because a perfectly good rear-drive roadster platform is a heck of a thing to waste.
In one of the strangest rumors we've heard recently, however, our compatriots over at Jalopnik report that the DeLorean Motor Company (yes, that DeLorean Motor Company) is considering buying the plant and the platform from GM and putting it back into production as a new DMC.

Junkyard Gem: 1986 Pontiac Fiero 2M4

The mid-engined, plastic-bodied Pontiac Fiero two-seater caused great excitement when it hit the streets as a 1984 model, then became something of an embarrassment for GM when its design flaws became clear to the car-buying public. Still, when a V6 engine became available for 1985, followed by a fastback roof for 1986, the air of Pontiac Excitement around the Fiero lingered to a certain extent. We took a look at a discarded '86 Fiero GT with both the 2.8-liter V6 and the fastback body last year, and now we'll take a look at an example of the econo-commuter four-cylinder notchback version from the same year. Pontiac used the 2M4 designation (standing for two seats, mid-engine, four cylinders) on four-cylinder Fieros, while the six-cylinder cars were known as 2M6s. 2M4 decals went on four-banger Fieros for the 1984-1986 model years, while 2M6 decals seem to have been applied less consistently to the V6 cars of that period. During the early development period of the car that became the Fiero, the idea was that it would be a nimble sports car with a lightweight engine. Then the plan shifted, with the Fiero intended to be a gas-sipping commuter. When the car finally hit showrooms, it was a lot heavier than intended, it had a Chevy Citation front suspension in the back plus a Chevette front suspension, and its engine was the low-revving, weighty Iron Duke 2.5-liter straight-four. The Duke was about the least sports-car-appropriate four-cylinder engine The General could dredge up from his parts bins, but it was cheap and there was no shortage of production capacity. By the time the Fiero came out, the Iron Duke had been renamed the Tech 4. This one was rated at 92 horsepower and 132 pound-feet. The V6 Fieros get all the press today, but plenty of the Duked versions were sold (amazingly, the Chevrolet Camaro was available with Iron Duke power from 1982 through 1986). The emissions sticker tells us that this was a California-market car, rather than the "49-state" model the rest of the country got. California-specific emissions hardware added $99 to this car's price ($277 in 2023 dollars). While this car is a base model, the original buyer loaded it with options. The transmission is a three-speed automatic, priced at $465 (about $1,303 in 2023 dollars). A five-speed manual was standard equipment on the 1986 Fiero, though the old-fashioned four-speed manual was still available for a $50 credit ($140 now).

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...