1996 Firebird T-tops 5 Speed Manual V-6 on 2040-cars

Auto blog

GM recalling 70k Chevy Malibus, Pontiac G6s over steering issue

A problem with the power steering system in the Chevy Malibu and Pontiac G6 has prompted General Motors and the National Highway Traffic Safety Administration to issue a recall for an estimated 69,633 vehicles. The issue revolves around the electric power steering assist, which could suddenly fail and increase the risk of a crash, especially at low speeds where the power steering is most helpful. The recall affects 2006-2007 Chevy Malibu sedans and Malibu Maxx wagons (specifically those manufactured between April 1, 2006, and June 30, 2006), as well as the Pontiac G6 (which was offered as a sedan, coupe or convertible) from the same model years and manufactured from April 18, 2006, to June 30, 2006. Owners of the affected units can expect to hear from the manufacturer with instructions to bring in their vehicles to their local dealers to have the torque sensors in the power steering system replaced. RECALL Subject : Sudden Loss of Electric Power Steering , 1 INVESTIGATION(S) Report Receipt Date: FEB 04, 2015 NHTSA Campaign Number: 15V064000 Component(s): STEERING Potential Number of Units Affected: 69,633 Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2006-2007 Chevrolet Malibu and Malibu Maxx vehicles manufactured April 1, 2006, to June 30, 2006, and 2006-2007 Pontiac G6 vehicles manufactured April 18, 2006, to June 30, 2006. In the affected vehicles, there may be a sudden loss of electric power steering (EPS) assist that could occur at any time while driving. CONSEQUENCE: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash. REMEDY: GM will notify owners, and dealers will replace the torque sensor assembly, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact Chevrolet customer service at 1-800-222-1020 or Pontiac customer service at 1-800-762-2737. GM's number for this recall is 14772. Note: This is an expansion of recall 14V-153 to cover additional vehicles built between April 1, 2006 and June 30, 2006. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Lutz says GM was working on 5th-gen Pontiac GTO

Bob Lutz was one of the forces behind bringing the Holden Monaro to the United States, as the ill-fated Pontiac GTO in 2004. And while that car received critical acclaim, it was a sales disappointment. Now, Road & Track is reporting that our suspicions were correct - Pontiac was working on a two-door, G8-based coupe before it was shuttered.
In that R&T article, which is no longer available online, Lutz explained that the new GTO would solve many of the issues found in the original. Car Advice speculates that the new model would have look like a rebadged version of the Holden Coupe 60 Concept from 2008, a conclusion we also came to.
That car would have been a big departure from the 2004 to 2006 GTO. It has an extremely long hood and short rear deck, with an almost fastback roofline and a wide greenhouse with a tall beltline. The wheel arches were very pronounced, and the chin and rocker panel splitters gave it a race-ready look. Would it have been enough to make the GTO work in the US? We think it might of, but it looks like we'll never know.

CNN chronicles young girl building Pontiac Fiero

At fourteen years of age, Kathryn DiMaria has already done what many self-proclaimed gearheads won't even attempt in their lifetimes. The Dearborn, Michigan teen is rebuilding a car from the ground up.
The intrepid youngster asked her parents when she was just twelve to start a Pontiac Fiero project, even offering to pony up all the funds herself. Father, Jerry DiMaria only expected the project to last a few months, but two years later, Kathryn is still at it. In this CNN video, the two are at Maker Faire (a DIY festival) rebuilding a 3.4-liter V6 engine out of a Chevrolet Camaro to replace the 2.8-liter mill found in the Fiero.
The whole family hast pitched in, with Kathryn's mother teaching her how to sew in order to complete the interior, father Jerry providing much of the technical know-how, and even her sister is chronicling Kathryn's progress through photos. Jerry even started a thread in a Fiero forum which has been live for two years and is now 22 pages long. Of the project, one forum member wrote, "welcome to the madness."