1998 Pontiac Firebird Trans Am Convertible 2-door 5.7l, One Owner 11,000 Miles on 2040-cars

Auto blog

Junkyard Gem: 1986 Pontiac Fiero GT

If you like affordable, mid-engined two-seaters, the 1980s were your decade. Fiat (and, a bit later, Bertone) offered the X1/9, Toyota sold MR2s, and even General Motors got into the act by creating the Fiero. Available from the 1984 through 1988 model years, the Pontiac Fiero showed plenty of promise but ended up being mostly disappointing, in some ways echoing the career of the Chevy Corvair of a couple of decades earlier. Today's Junkyard Gem is a once-spiffy 1986 Fiero GT, found in a self-service yard near Denver, Colorado. After a long and painful development period stretching all the way back to John DeLorean's XP-833 Banshee (which ended up being a major influence behind the original Opel GT), the Fiero finally debuted in 1983 as a 1984 model. The top-of-the-model-range GT appeared the following year. The Fiero was built as a notchback coupe and as a fastback, with all the GTs being the latter type. I couldn't get the engine lid open, but this car would have left the assembly line (in Pontiac, Michigan) with a 2.8-liter V6 rated at 140 horsepower. This car has a five-speed manual transmission, making it a credible rival for Toyota's MR2.  The 1986 MR2 was less powerful than the Fiero GT (112 horsepower versus 140), but also scaled in significantly lighter (2,459 pounds against the Pontiac's 2,780 pounds). The MR2 also cost less, priced at $11,298 while the Fiero GT cost $12,875 (that's about $30,540 and $34,805, respectively, in inflation-adjusted 2022 dollars). Meanwhile, the $6,998 Honda Civic CRX two-seater lured away many potential Fiero buyers despite being a front-engined/front-wheel-drive car, and the $7,186 Ford EXP/Mercury LN7 also put a dent in Fiero sales. I can't find a price for the 1986 Bertone X1/9, but it cost a hard-to-believe $13,990 in 1984. GM still was using five-digit odometers in many vehicles by the middle 1980s, but this Fiero has a six-digit unit and thus we can see that it nearly achieved 150,000 miles during its driving career. The 1984-1987 Fiero suffered from a parts-bin suspension design, with the front suspension borrowed from the Chevrolet Chevette and the entire rear transaxle/suspension assembly lifted from the front end of the Chevrolet Citation. For the 1988 model year, GM finally spent the money to design an improved Fiero-specific suspension … and then promptly put a halt to production.

Automakers tussle over owners of 'orphan' makes

When General Motors put down several of its brands in recent years, it also let loose thousands of brand-loyal customers who will eventually need another car.
R.L. Polk Associates estimates there are more than 18 million cars from 16 discontinued makes on the road today. Those "orphan owners" have sales-hungry competitors seeing dollar signs. GM is offering Saturn owners $1,000 cash toward a Chevy Cruze, Cadillac CTS or a GMC Acadia. Ford is giving its Mercury lease customers a chance to get out of their contracts with no early-termination penalty and offering to waive six remaining payments if they drive off in a Ford or Lincoln.
Edmunds.com research shows the efforts are paying off somewhat for GM, with 39 percent of Pontiac owners, 37 percent of Hummer owners and 31 percent of Saturn owners taking delivery of another GM-branded vehicle. But that leaves as much as 69 percent of owners going elsewhere. Ford, Honda and Toyota seem to be attracting many former GM owners.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...