2006 Mercury Mariner Premier Auto Fwd..leather..3.0l V6 on 2040-cars

Auto blog

Junkyard Gem: 1979 Mercury Marquis 2-Door Sedan

As the creator of the now-much-overused term "Malaise Era" (which I say started in 1973 and ended in 1983, full stop), I have a certain affection for the big two-door Detroit cars of the late 1970s. When such a car is built on the very first model year of Ford's long-lived Panther platform and I find one in a junkyard, I must document it. The 1979 Mercury Marquis is such a car, and this one was found in a San Francisco Bay Area self-service yard last month. Since Ford built the Grand Marquis all the way through the demise of the Panther platform— and Mercury itself— in 2011, it's easy for us to forget that the model name started out as just the plain old Marquis, back in the 1967 model year, with the Grand appellation used for the car's top trim level. While today's Junkyard Gem has some of the features of the Grand Marquis and Marquis Brougham trim levels for 1979 (notably the padded vinyl landau roof and power windows), it lacks the huge chrome lower-body moldings of those cars. Instead, it's a regular Marquis 2-door sedan with a big load of expensive options. That landau roof has suffered greatly from its decades beneath the vinyl-disintegrating California sun. The Panther platform was a big technological upgrade from the late-1950s-vintage chassis technology of full-sized Fords of the 1960s and 1970s, and it stayed in front-line service in much the same form through 2011. Though its ride and handling were much improved, the 1979 Marquis was quite a bit smaller than its predecessors, and that caused some grumbling among Mercury shoppers. Some ham-handed junkyard shoppers really tore up the interior of this car while extracting a few bits and pieces, but we can still admire the Pine Green pleather of the glorious Twin Comfort Lounge front seats. You had two engine choices when buying a new '79 Marquis: the base 302-cubic-inch (5.0-liter) Windsor V8 making 129 horsepower or the optional 351-cubic-inch (5.8-liter) Windsor V8 rated at 138 horsepower. This one appears to be the 351, the same engine as had been swapped into the pizza-delivery Mercury I drove in the middle 1980s. New cars sold in California around this time had these giant emissions-numbers stickers on the side glass. Later, they went on the underside of the hood.

Curtain officially comes down on Mercury as dealers remove signage

The process of shutting down the Mercury is complete. Ford officially made the decision to close its mid-level brand in June of 2010. In the months that followed, Ford offered its dealers money to stop selling the cars, with production shutting down in September. The last Mercury, a Mariner, rolled off the assembly line in the beginning of October and former spokesperson Jill Wagner said her good-byes to both the car and her job. Now the last piece of the brand has come down as dealers are removing any and all Mercury signage from their lots.
[Source: Detroit News]Read | Permalink | Email this | Comments

NHTSA investigating Ford's solution to May 2014 power steering recall

The National Highway Traffic Safety Administration is investigating a complaint that Ford's response to a May 2014 recall of the 2008 to 2011 Ford Escape and Mercury Mariner doesn't quite go far enough to solve a troubling power-steering problem. Roughly a year ago, Ford recalled nearly a million vehicles after it was found that a problem with the torque sensor's communication with the power steering control module could cut steering assistance for drivers. While manual steering would still be available, the problem was enough to ask drivers to report in to have the PSCM inspected, and if necessary, replaced (along with the torque sensor, or in dramatic cases, the entire steering column). That would only happen, though, if trouble codes were being thrown. If there weren't any problems, dealers were told to simply update the PSCM's software so that any issues between it and the torque sensor would simply throw a visual and audio warning – power steering would still be maintained. The petitioner claimed that following the recall work, he still experienced a problem with the torque sensor. According to NHTSA, a claim was made that Ford didn't go far enough in its solution to the problem, and that "the software update itself may in fact cause further issues with the affected vehicle's power steering, causing it to fail, and ultimately requiring replacement of the torque sensor or entire steering column." The petition was filed in early February and is now officially being looked into by NHTSA.