2005 Mercury Premier Sport Utility 4 Door on 2040-cars

Auto blog

Ford recalling 126,000 Fusions and Milans over wheel separation concern

Ford has announced a recall of certain Ford Fusion and Mercury Milan vehicles after an investigation by the National Highway Traffic Safety Administration. A total of 128,616 2010 and 2011 models equipped with steel wheels may have been manufactured with wheel studs that could crack and split over time. If that happens, the vehicle may experience a wheel separation.
According to The Detroit News, the company is aware of a total of 30 wheel separation incidents, one of which occurred on the front of the vehicle. Even so, no injuries have been reported as a result of the defect.
The problem apparently stems from the fact that the mounting pads on the vehicles' steel wheels may have been faulty from the factory. In addition, the wheel mounting face on rear disc brakes may not have been installed properly. Ford will inspect the rear disc face and replace them as necessary. In addition, the company will replace all of the vehicle's wheel studs free of charge. Head to the NHTSA website for more information, and click past the jump to view the full recall notice.

Junkyard Gem: 1993 Mercury Topaz GS Sedan

As long as the Mercury brand existed — a period spanning the 1939 through 2011 model years — nearly every Mercury sold in the United States was more or less a redecorated Ford model. The Torino had its Montego sibling, the Crown Victoria had the Grand Marquis, the Cougar was based on everything from the Mustang to the Mondeo, and so on. Naturally, when the folks in Dearborn developed the Ford Tempo compact, a Mercury version had to be created. This was the Topaz, with the official launch of both cars taking place on the deck of the aircraft carrier often referred to as the USS Decrepit. You can't make this stuff up! The Tempo/Topaz, also known as the Tempaz, has largely faded from our collective automotive memory by now, since it broke no significant new engineering or styling ground (this story would be much different if Ford had only put the amazing straight-eight "T-Drive" Tempaz powertrain into production) and didn't have any endearing features other than being a cheap domestic competitor to the Toyota Corolla and Nissan Sentra. Still, close to 3 million Tempazes left North American Ford and Lincoln-Mercury showrooms during the 1984-1994 period. As you'd expect, most of these disposable cars disappeared from both the street and the car graveyard long ago. It takes a very special Tempaz for me to break out my camera while I'm patrolling my local wrecking yards; generally, this means an ultra-rare all-wheel-drive version or at least a very early model in super-clean condition. Today's Junkyard Gem is neither, but I took one look at this spectacular Bordello Red crypto-velour-and-slippery-plastic interior and recognized that this was no ordinary junkyard Mercury. It appears that Mercury had dropped the idea of clever names for base-grade seat fabrics by the time of the Topaz, referring to this stuff as just "cloth" in all the brochures I could find. That's too bad, because Mercurys had cool names for upholstery (e.g., Chromatex) in the old days. The interior is in very good condition but the steering wheel shows substantial wear, so I think this is a high-mile Topaz that got meticulous care from its owner or owners. Ford used five-digit odometers on these cars until the end of production, however, so we'll never know if this reading indicates 65,404 miles or 365,404 miles. The body is very straight, but there's some nasty corrosion behind the right front wheelwell.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: