2009 Mercury Grand Marquis Ls on 2040-cars

Auto blog

NHTSA and Ford investigating steering issues in Crown Vic, Grand Marquis and Marauder

There may be more steering woes for the Ford Crown Victoria. The National Highway Traffic Safety Administration has opened a preliminary evaluation into the Crown Vic and Mercury Grand Marquis from the 2004 to 2007 model years and the Mercury Marauder for the 2004 and 2005 model years because the steering shaft can jam. The issue could potentially affect an estimated 500,000 vehicles.
According to the regulator, there is a possibility that the driver's side heat shield for the exhaust manifold can rust, dislodge, and then wedge into the steering shaft. If this occurs, it leads to a situation where the driver can no longer control the car.
NHTSA has received five complaints of this happening, including one alleged case with an injury. In that situation, the car was driving onto the highway, lost control and rolled over. One occupant was hurt in the accident.

This Mercury Cougar Eliminator is a lovely '69 survivor

If you have an overachieving brother/sister/cousin/friend (or whoever), you might know this feeling well; it can be tough to live up to those standards. In many ways, that notion can also describe the Mercury Cougar and its pioneering Ford Mustang sibling. Quite the act to follow, no? Happily though, the Cougar proved to be different enough from its Mustang relative to make a big splash, and perhaps no more so than in its racy "Eliminator" trim, new for 1969. This is one such heady Mercury, dressed in sporty Competition Orange paint, and claimed to be an unrestored "survivor." Need it in your life? The '69 Mercury Cougar Eliminator recently popped up on eBay in Chepachet, Rhode Island . The genesis of the Mercury Cougar began in 1967, really with one singular purpose—to bridge the gap between the Ford Mustang and the Ford Thunderbird with a more upscale, stylish, and chiefly more "European" feeling pony car. It's safe to say the Cougar fit the bill. Using the Mustang chassis as a base, the early Cougars were about three inches longer than their 'Stang cousins and offered better legroom, sleek front and rear fascias, and a more luxe interior. Don't mistake "upscale" for "soft" however; come 1969 the Eliminator package gave the Cougar a seriously mean attitude. Spec-up the interior package and you received high-back bucket seats, a Rallye clock, wood-rimmed steering wheel, and padded interior moldings among other custom trims. Outside is where the Eliminator really struts its stuff, though. Eliminators came equipped with a blacked-out grille, special steel wheels, an aggressive front splitter and rear wing, plus racy decals and side stripes. Four color choices were available — Competition Orange, Bright Blue Metallic, White, and Bright Yellow. As standard, the '69 Mercury Cougar Eliminator came equipped with a 351 cubic inch V8, boasting 290 horsepower, as seen in the case of this car. More powerful options were also available, as noted by Barnfinds, which included a big 390 cubic inch V8 (320 hp), a high-revving Boss 302 V8, and the gargantuan 428 Cobra Jet V8. Peek beneath the body of this Cougar and the 351ci V8 is hooked up to a desirable close-ratio four-speed manual transmission, showing a claimed 35,243 miles. Though the mileage isn't verified, the car's overall condition and wear would suggest the readings to be true. Befitting those low miles, this unrestored Cougar does carry quite the high price — a tall $32,000.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: