1972 Mercury Grand Marquis on 2040-cars

Auto blog

Ford recalls over 953,000 vehicles to replace Takata airbag inflators

DETROIT — Ford is recalling more than 953,000 vehicles worldwide to replace Takata passenger airbag inflators that can explode and hurl shrapnel. The move includes over 782,000 vehicles in the U.S. and is part of the largest series of recalls in U.S. history. Included are the 2010 Ford Edge and Lincoln MKX, the 2010 and 2011 Ford Ranger, the 2010 to 2012 Ford Fusion and Lincoln MKZ, the 2010 and 2011 Mercury Milan, and the 2010 to 2014 Ford Mustang. Some of the recalls may be limited to specific geographic areas of the U.S. Takata used the chemical ammonium nitrate to create an explosion to inflate airbags. But it can deteriorate over time due to heat and humidity and explode with too much force, blowing apart a metal canister designed to contain the explosion. At least 23 people have been killed worldwide and hundreds injured by the inflators. Ford says it doesn't know of any injuries in vehicles included in this recall. Dealers will replace the inflators. Ford will notify owners about the recall starting on Feb. 18, and the company has replacement parts available for dealers to order, said spokeswoman Monique Brentley. In previous Takata recalls, parts availability had been an issue. Owners can go to this Ford website and key in their vehicle identification number to see if their cars and SUVs are being recalled. The same information will be available soon at the NHTSA recall website. More than three years after the U.S. National Highway Traffic Safety Administration took over management of recalls involving Takata inflators, one third of the recalled inflators still have not been replaced, according to an annual report from the government and a court-appointed monitor. The report says 16.7 million faulty inflators out of 50 million under recall have yet to be replaced. And 10 million more inflators are scheduled to be recalled this month, including the Ford vehicles. Safety advocates said the completion rate should be far higher given the danger associated with the inflators. The recalls forced Takata of Japan to seek bankruptcy protection and sell most of its assets to pay for the fixes. The inflators grow more dangerous as they get older because ammonium nitrate deteriorates due to high humidity and cycles from hot temperatures to cold. The most dangerous inflators are in areas of the South along the Gulf of Mexico that have high humidity. Related Video:

NHTSA will investigate some Ford Fusion, Lincoln MKZ models for power steering issue

The National Highway Traffic Safety Administration is opening an investigation into the 2010-2012 Ford Fusion, Fusion Hybrid and Lincoln MKZ, the 2012 MKZ Hybrid and 2011 Mercury Milan because the agency has hundreds of complaints of electric power steering failure in these models.
According to NHTSA's data, it has received 508 complaints of the power steering allegedly suddenly malfunctioning and resulting in increased effort to turn the wheel. In four incidents, these failures resulted in loss of control and crashes. According to the reports, in some cases a power steering warning message came on as the fault occurred, and other times the system restored itself by turning off and then restarting the vehicle. NHTSA said it has also received further field report data from Ford, but that information hasn't been publicly released yet.
For the moment, there isn't a recall for this failure on these models. NHTSA is just investigating them to "assess the scope, frequency and safety consequences of the alleged defect," and the agency says an estimated 938,000 vehicles could potentially be affected.

The 1965 Ford Mustang could have looked a lot different

The 1965 Ford Mustang is unquestionably an automotive design icon, and nearly every generation of Mustang has some connection to that original car. Because it's such a universally-known vehicle, we were amazed to see all the different designs that were being considered. Head of Ford's archives Ted Ryan recently shared photos of design proposals for the original Mustang on Twitter that he and Jamie Myler found, and we reached out to them to find out more. As Ryan initially noted, the photos were taken on August 19, 1962, and they are proposals for the Ford Mustang. Apparently Ford had committed to doing a Falcon-based youth-oriented car at this point, and it did have plans to launch the car in 1964 for the 1965 model year. But after having little success with early design proposals, the company asked all of its design studios — the Advanced Studio, Lincoln-Mercury Studio and Ford Studio — to submit proposals. With only about two years before the planned launch, Ford was understandably short on time, and it's believed that the studios only had a month to create and present these designs. Lincoln-Mercury design proposal View 8 Photos The majority of the designs, a total of five, came from the Advanced Studio, and part of this was because they already had a couple of concept designs in reserve it could present. Two other models representing three design possibilities came from Lincoln-Mercury, and just one model with two options came from Ford. The Advanced Studio proposals are shown in the gallery at the very top of this article, and the Lincoln-Mercury and Ford proposals are in the gallery directly above this paragraph. The Advanced Studio's most radical design is the one that was clearly related to the Mustang I concept that would be shown later that year with huge wraparound rear glass, turbine-inspired bumpers and enormous side scoops. The other proposals from the studio were more conservative, featuring simple lines, grilles reminiscent of the Falcon, and one even borrowing the jet-thruster-style taillights made famous on the Thunderbird. Lincoln-Mercury had some impressively bold designs, particularly its fastback that had buttresses to extend the shape all the way to the tail. This car had two different side trim possibilities. The other Lincoln-Mercury design was toned down a bit, but had two interesting possibilities for side detailing, as well as some crisp, low-profile tail fins.