Low Mileage 49k, New Battery & Alternator, Superior Performance, One Owner on 2040-cars

Auto blog

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.

Junkyard Gem: 1972 Mercury Cougar XR-7

Starting with the 1939 model year and continuing through 2011, the rule in Dearborn was that most Ford models would get a dressed-up sibling wearing Mercury badges (and Canadians even got Mercury F-100s and Econolines). When the Mustang first hit showrooms in 1964, the countdown for a Mercurized version began. That car, the Cougar, debuted as a 1967 model marketed as "the man's car." Today's Junkyard Gem is a much-abused example of the early-1970s Cougar, found in a San Francisco Bay Area car graveyard a while back. Just as the Mustang packed on weight and price as the 1960s became the 1970s, the even more heavily gingerbreaded Cougar did the same. For 1971 through 1973, the Cougar was still based on the Mustang chassis but weighed several hundred additional pounds and was more than seven inches longer. The curb weight for this car was 3,298 pounds, versus 2,941 pounds for the lightest '72 Mustang coupe. Yes, there's a Mustang underneath all that chrome! When the Mustang went to a modified Pinto chassis starting in the 1974 model year, the Cougar moved over to the midsize Torino platform and stayed there until it rejoined the Mustang on the Fox platform for 1980 (though the honor of being the Mustang's near-twin went to the Mercury Capri at that point). For 1989, the Cougar became an MN12 Thunderbird sibling, where it remained through its 30th anniversary … and then the Cougar got the axe. The Cougar story wasn't done at that point, however, because the name got revived in 1999 with a Mondeo-based version that lasted through 2002 and bears the distinction of being one of the few Mercury models with no corresponding Ford-badged counterpart. Along the way, there were Cougar sedans and even station wagons, with the curb weight of the heaviest-ever Cougar bloating to well over two tons (the winner of that honor is the 1977 Cougar Villager wagon, scaling in at an astounding 4,482 pounds). In 1972, though, all new Cougars were coupes or convertibles, and all of them came with factory V8 power. The build tag on this one tells us that it was assembled at the River Rouge compound in Dearborn and sold via the Kansas City sales office. That tells us that someone drove this car to California after buying it in the Midwest; Ford also built 1972 Cougars in San Jose, so California Mercury shoppers would have bought locally-produced ones. It's a top-end XR-7 in Medium Bright Yellow paint, with the interior in Medium Ginger.

Ford recalls 600,000 older-model sedans for braking issue

Ford is recalling 600,166 older-model Ford, Lincoln and Mercury vehicles over an issue that could affect braking and increase the risk of a crash. The safety recall covers certain Ford Fusion, Mercury Milan and Lincoln MKZ sedans from the 2006 through 2010 model years that were built at Ford’s Hermosillo Assembly Plant in Mexico between Feb. 22, 2006, and July 15, 2009. Ford says a valve that is normally closed inside the hydraulic control unit may get stuck in the open position or be slow to close, which could make it harder to engage the brakes and increase risk of a crash. Ford says itÂ’s aware of 15 reports of accidents and two injuries possibly related to the issue. Dealers will inspect the hydraulic control unit for signs of the problem and replace it, if necessary. The dealers will pressure-flush the system with brake fluid and replace the reservoir cap with a new one. Ford is also issuing a small recall of 33 of its 2020 F-150 trucks in the U.S. and 51 in Canada over potentially damaged spare tires. It says the bead area on the tires may have been damaged when it was mounted onto the wheel assembly, leaving it vulnerable to corrosion, separation of the bead wire and ultimately a rapid loss of air pressure and detachment from the wheel. Dealers will replace the spare tire. Affected vehicles were built at the Dearborn Truck Plant from Nov. 10-21 of this year.