1949 Mercury Custom on 2040-cars

Auto blog

NHTSA and Ford investigating steering issues in Crown Vic, Grand Marquis and Marauder

There may be more steering woes for the Ford Crown Victoria. The National Highway Traffic Safety Administration has opened a preliminary evaluation into the Crown Vic and Mercury Grand Marquis from the 2004 to 2007 model years and the Mercury Marauder for the 2004 and 2005 model years because the steering shaft can jam. The issue could potentially affect an estimated 500,000 vehicles.
According to the regulator, there is a possibility that the driver's side heat shield for the exhaust manifold can rust, dislodge, and then wedge into the steering shaft. If this occurs, it leads to a situation where the driver can no longer control the car.
NHTSA has received five complaints of this happening, including one alleged case with an injury. In that situation, the car was driving onto the highway, lost control and rolled over. One occupant was hurt in the accident.

Ford recalls 300,000 Crown Vics over lighting module

The Basics: Ford is recalling 312,814 units of the Crown Victoria and Mercury Grand Marquis sedans from the 2003-2005 model years. They were built at the St. Thomas Assembly Plant between Oct. 3, 2001, and Aug. 2, 2005. Ford says 296,004 of those units are located in the United States, with another 14,714 in Canada and 2,096 in Mexico. The Problem: The solder joints on the lighting control module could crack, depriving the headlamps of the power they need to light the way ahead. That could increase the risk of a crash, particularly at night and in other low-visibility situations. Injuries/Deaths: Ford reports that it is aware of 11 accidents that resulted from the problem, leading to one injury described as "minor." The Fix: The manufacturer is instructing dealers to replace the entire lighting control module. If You Own One: Make sure your headlights are working before getting under way. If they're not, avoid driving under low-light conditions, including at night, in heavy precipitation, or in fog. Ford Issues Three Safety Recalls and One Safety Compliance Recall in North America DEARBORN, Mich., Dec. 22, 2015 – Ford Motor Company is issuing three safety recalls and one safety compliance recall in North America. Details are as follows: Ford Motor Company issues safety recall for certain 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles to replace lighting control module Ford Motor Company is issuing a safety recall for approximately 313,000 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles to replace a lighting control module. The solder joints on the module could crack and interrupt power to the headlamps – increasing the risk of crash at night. Ford is aware of 11 reports of accidents and one report of a minor injury related to this issue. Affected vehicles include certain 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles built at St. Thomas Assembly Plant, Oct. 3, 2001 through Aug. 2, 2005. There are a total of 312,814 vehicles that might be affected in North America, including 296,004 in the United States and federalized territories, 14,714 in Canada and 2,096 in Mexico. Dealers will replace the lighting control module at no cost to the customer. Ford issues safety recall for certain 2016 Ford F-650 and F-750 vehicles to replace rear air brake chamber Ford is issuing a safety recall for 177 2016 Ford F-650 and F-750 vehicles to replace the rear air brake chamber.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: