1994 Mazda Miata Convertible 2-door 1.8l on 2040-cars

Auto blog

Mazda G-Vectoring Control makes driving better without you knowing

Mazda has just spent eight years developing a new technology that will make its new cars a lot more fun to drive, even if you have absolutely no idea that it's working. And subtlety's the point, Mazda engineers told us at a press event at Mazda Raceway Laguna Seca. In fact, the effects of what they've dubbed G-Vectoring Control are so fine that the marketing and PR teams are at a loss for how to do their jobs with it. "The engineers have done their work," said Mazda Director of Communications Jeremy Barnes, "But how do we get the message across?" The basic premise is this: G-Vectoring activates only when the car's on-board computer reads simultaneous steering and throttle input. The data — including throttle position, steering angle, and, crucially, how quickly you're adjusting the steering angle — are then funneled through an algorithm to reduce engine torque, which transfers vehicle weight, adding more grip to the wheels that need it. The system will appear first on 2017 Mazda6 sedans arriving in showrooms later this year, followed by the 2017 Mazda3. Actually, "subtle" does not even begin to describe the effect. G-Vectoring Control can detect as much as one tenth of one degree of steering angle, and changes the cornering forces only 0.1 to 0.5 g as a result. "That's less than the human body can feel," explained Vehicle Development Engineer Dave Coleman. In practice, G-Vectoring reduces the steering angle at turn-in, as well as the rate at which one turns the wheel. To demonstrate, Director of R&D Kelvin Hiraishi rode shotgun with us in a specially equipped Mazda6 that allowed him to turn G-Vectoring on or off at the push of a button (production cars will always have it on). Hiraishi had us drive a number of courses, including Mazda Raceway Laguna Seca itself, while an engineer measured our steering inputs with a laptop Matrix'd into the car's electronic brain. I drove the same course several times with the same car in the same conditions, with cruise control locked and the system turned on or off. Lo and behold, with G-Vectoring activated, the engineer's output graph showed that my steering inputs were indeed reduced ever so slightly. There were two times that G-Vectoring was markedly noticeable. The first on a turn with a minor banking toward the outside, and the second was during cornering over an artificially wet section of the course — in other words, when the car was at the limits of adhesion.

2015 Mazda3 shows its shape

Mazda's new Kodo design language is set to quickly spread across the automaker's entire lineup, judging by these spy shots of the next-generation Mazda3 that show some very familiar styling cues. No matter, we're impressed with what Mazda has done on the CX-5 crossover and Mazda6 sedan in terms of design, and we're happy to see the C-segment hatchback ditching the smile-for-a-mile Nagare design.
It's unclear what sort of architecture is found below the new Mazda3 - our spy shooters suggest that the car could simply be using a heavily massaged version of the Ford C1 platform found under the current car. Our best guess is that it's actually a reworked version of the platform used in the CX-5 crossover, however, chocked full of weight-saving Skyactiv technologies. After all, the CX-5 plays in the compact CUV segment, and those vehicles are commonly based on C-segment platforms. And besides, there's probably some economic savings at work with the new chassis - both in terms of fuel efficiency and economies of scale. Still, no one is totally certain what lies under all that black-and-white paper at the moment.
The new Mazda3 is targeted to arrive for the 2015 model year, meaning we could see a final production car debut as early as this year. We expect the hatch you see here to debut along with a traditional four-door sedan, and unless we hear otherwise, we don't doubt that a Mazdaspeed version will be far behind.

Mazda just restored the 787B's forgotten older brother

Among Mazda's many racecars, none is as famous as the 787B, and for good reason. The 787B remains the only Japanese car and the only rotary-powered car to win overall at the 24 Hours of Le Mans. It wasn't Mazda's only successful endurance racer, though. Before the 787B, there was the 767B. Mazda's 767B racecars competed in the IMSA GTP class at endurance races throughout 1989. They featured 630-horsepower four-rotor engines and were very successful in their class. This newly restored car took first and second place class finishes in five of the six races it participated in, and each finish was in the overall top ten. The one exception was a DNF in which the transmission failed. Twenty-five years after the 767B's glory days, Mazda initiated a complete teardown and restoration of the aged car. The work was done by Downing Atlanta and supervised by former Mazda racers Rick Engman and Jim Downing. (Fun fact: Downing was one of the designers of the HANS device.) The shop has also restored other racecars for Mazda, including one of the 787Bs. The car went through a two-year rehab and will make its track re-debut at the Monterey Motorsports Reunion. The event takes place next weekend at Mazda Raceway Laguna Seca where the track will once again feature the angry shriek of a competition-grade rotary engine. Related Video: Image Credit: Mazda North American Operations Motorsports Mazda Automotive History Racing Vehicles Pebble Beach