2006 Lexus Rx on 2040-cars

Auto blog

Lexus ES350 confirmed for Kentucky production starting in 2015

Following Thursday's report, Toyota has confirmed that production of the Lexus ES will move to its Georgetown, KY assembly plant starting in 2015. To accommodate the extra 50,000 units of capacity that the ES represents, Toyota will be investing $360 million in the plant and hiring 750 new workers.
In the previous report, sources stated that the state of Kentucky had offered Toyota as much as $146.5 million to move ES production to the Georgetown facility.
The press release, posted below, specifies that only the ES350 will be built in Kentucky, so it's likely that the ES300h hybrid will continue to be built in Japan - where all ES models have been built since the car was introduced in 1989. Toyota's Georgetown plant, which currently builds the Toyota Camry, will also be getting an expansion to its engine plant to produce more four-cylinder engines at a cost of $30 million and will create an additional 80 jobs.

Toyota recalls 337,000 RAV4s and HS250h models for tie rod failure

UPDATE: The post has been updated with additional information from NHTSA. The Basics: Toyota is recalling 337,000 2006-2011 model year Toyota RAV4 crossovers built between October 31, 2005 and September 7, 2010 as well as 2010 model year Lexus HS250h cars built between July 6, 2009 and August 26, 2010. The Problem: When either an affected RAV4 or HS250h is given an alignment and the tie rod adjustment nut on the rear control arm isn't tightened properly, the threads on the tie rod can start to rust. If this happens, the nut may break off and throw off the alignment drastically and suddenly. This isn't a case of the car simply pulling to one side, either. This would seriously upset the balance of the car and could cause the driver to lose control and crash. This is also the third time these vehicles have been recalled for the same issue. Injuries/Deaths: It's unknown if this control arm issue has resulted in any injuries or deaths. Autoblog reached out to Toyota for more information, but a company representative told us that the company isn't able to discuss injuries or deaths caused by this issue (if any) at this time. Based on information from NHTSA documents, it does not appear that any crashes, injuries or deaths have been attributed to the defect addressed in the current recall. The Fix: The dealer will completely replace the rear suspension assemblies at no cost to the owner. The tie rods and nuts will also be coated in epoxy to prevent future rusting from occurring. According to Car and Driver, the previous recalls involved tightening nuts, coating decent tie rods in epoxy and completely replacing rusted ones. The car magazine reports that further complaints were filed and the company is now replacing all components regardless of condition. If you own one: Toyota will notify owners of affected cars by mail. Owners can also check whether their cars are affected by entering the VIN at safercar.gov/vin. Owners with questions can also reach Toyota customer service at 1-800-331-4331 or Lexus customer service at 1-800-255-3987. Related Video: Featured Gallery 2012 Toyota RAV4 View 16 Photos News Source: Car and Driver, Toyota, National Highway Traffic Safety AdministrationImage Credit: Toyota Recalls Lexus Toyota Safety lexus hs 250h lexus hs250h

2014 Lexus IS gets TRD bits

Toyota Racing Development (TRD) in Japan has designed cosmetic and performance bits that give the 2014 Lexus IS a front-to-back workover. Different from the F-Sport parts we expect from Lexus here, the full body kit runs 437,700 yen ($4,285 US) and starts with air deflectors at the lower edges of the front bumper, through to side skirts, a decklid spoiler and a rear bumper with a diffuser and quad exhaust tips.
For 288,750 yen ($2,830) you can sharpen responses with new shocks, springs, dampers, sway bar and bracing. The priciest individual component is the set of 19-inch wheels, four of them going for 527,625 yen (5,170 US). There's no word on US importation or pricing yet, but done up all in black like the IS above, we wouldn't mind seeing it here.