2007 Infiniti G35x, Salvage Damaged, Wrecked. Crashed, Runs And Drives, Sedan on 2040-cars

Auto blog

Infiniti Prototype 9 is a wonderfully beautiful EV grand prix car

Few automobiles are as elegantly beautiful as the open-wheel grand prix cars of the 1940s, '50s and '60s. The simple, slender shapes of these cars bear no extravagant flourishes or adornments. The purposeful design is what gave these cars their beauty, and it's these classic machines that inspired the new Infiniti Prototype 9. Teased earlier this week, this concept blends old and new, with classic lines hiding a modern all-electric powertrain. The Prototype 9 will make its full debut next week at the 2017 Pebble Beach Concours d'Elegance. Infiniti says the car was built around a simple idea: what would a 1940s Infiniti grand prix car look like? While the silver paint may be more German than Japanese, the design could easily be mistaken for an actual '40s grand prix car. Only the Infiniti-styled grille gives it away. Everything about it, from the thin bias-ply tires wrapped over center-locking wire wheels to the bulging screws around the driver's seat, is pitch perfect. Underneath that achingly long hood rests a prototype electric motor and battery from Nissan's Advanced Powertrain Department. The combo sends 148 horsepower and 236 pound-feet of torque straight to the rear wheels. That's good enough to send the svelte 1,962 lb car to 62 mph in just 5.5 seconds. Top speed is right at 106 mph. While speed may die off towards the top end, all that torque and a 43/57 front to rear weight distribution should make the Prototype 9 a riot on a small, tight circuit. There's only enough juice in the battery for about 20 minutes of flat-out racing. The handmade steel body rests on a steel ladder-frame chassis. The front suspension uses a leading-arm rigid axle with transverse leaf spring while the rear uses a De Dion axle, also with a transverse leaf spring. The Prototype 9 also uses old-school hydraulic rotary type dampers. There's no power steering and no brake booster for the four-wheel disc brakes. The car was designed and built by a number of different departments within Infiniti and Nissan. A simple sketch expanded as more and more designers and engineers wanted to have a hand in the project. The steel body panels were all shaped and hammered by hand. The bare cockpit is only adorned with a thin seat, three gauges, a few switches, a gear selector and the steering wheel. The gauges are set into a fixed aluminum hub in the center of the steering wheel.

Infiniti puts EV plans on hold again

Think of it as the green-automotive industry's version of Groundhog Day. Nissan's Infiniti division is putting plans for its first mass-production electric vehicle on hold. Again. The Infiniti LE, whose concept version was unveiled 2012's New York Auto Show, is again being put up on the proverbial blocks, USA Today says, citing a presentation by Infiniti executive Michael Bartsch at a recent company event in Detroit. Essentially, the Nissan division has bigger fish to fry, in the form of boosting overall Infiniti sales, and doesn't yet want to put the effort into introducing the Infiniti LE. The Infiniti EV plans were first postponed by then-Infiniti President Johan de Nysschen during the summer of 2013, as de Nysschen wasn't quite buying into Nissan boss Carlos Ghosn's ambitious electric vehicle sales projections. De Nysschen resigned last summer to join General Motors' Cadillac division. One issue may be the fact that the Infiniti wouldn't be all that different from the Nissan Leaf. Despite the fact that US sales of that EV surged 34 percent last year compared to 2013, to 30,200 vehicles, an Infiniti version was apparently not enough of a selling point within the company. While the Infiniti is sportier looking than the Leaf and would boast inductive, wireless charging, it would have a similar power output and single-charge range as the Leaf.

Mercedes and Infiniti confirm joint production in Mexico [w/video]

It's official, folks: After initial reports last week indicated that Mercedes-Benz was preparing to begin assembly at the Nissan plant in Aguascalientes, Mexico, the two parent companies have announced just that. Only instead of using the existing Nissan plant at the site (in operation since 1992), Daimler and the Renault-Nissan Alliance have announced a joint venture to build a new one alongside it.
The latest stage in the growing French-German-Japanese collaboration is part of a new collaboration that will see Infiniti and Mercedes jointly develop and build a line of compact premium vehicles, with the first Infiniti models set to roll off the assembly line in 2017 and the first Benzes to follow a year later. Neither party announced exactly which models that would encompass, but Mercedes already has a robust line of small vehicles (including the A-Class, B-Class, CLA and GLA), and Infiniti has long been toying with the idea of slotting in something smaller below the Q50.
The billion-euro project, split evenly between the two industrial giants, is set to create 5,700 new jobs in Mexico. In addition to the Aguascalientes project, Infiniti and Mercedes are also undertaking joint production of four-cylinder engines (initially for the C-Class and Q50) in Decherd, Tennessee, from which they will be exported around the world. By the time the new factory in Mexico reaches full capacity in 2021, it will have the capability to produce 300,000 vehicles annually. That's on top of the 850,000 vehicles the existing facility is capable of handling.