2008 Honda Civic Lx Sedan 4-door 1.8l on 2040-cars

Auto blog

Honda underreported 1,729 claims of injuries or deaths since 2003

Among these underreported cases were eight Takata airbag inflator ruptures not submitted. Following an independent audit of its safety reporting procedures, Honda has found massive holes in its methodology and practices that resulted in 1,729 claims of injuries or deaths going unreported to federal authorities dating back to July 2003. The cases should have been submitted to the National Highway Traffic Safety Administration as part of its quarterly Early Warning Reports (EWRs) under the TREAD Act, but they fell through the cracks for a variety of reasons. Honda blames the underreporting on three factors: data entry errors, computer coding problems and "an overly narrow interpretation of what constituted a 'written notice' under the TREAD Act." The first two issues were related to the computer program that collected the claims. If employees didn't enter a date in the "written claim received" field, then they were omitted from the EWRs. Also, the company's internal component codes didn't always match those used by NHTSA, and only the ones that were the same were disclosed. Finally, third-party documents, including police reports, were not considered. Honda says the computer error is now corrected, and the company is updating its data entry training. In the future, written and oral claims will be included in EWRs, as well. Among these underreported cases were eight Takata airbag inflator ruptures not submitted in Honda's EWRs, including one death and seven injuries. However, the automaker claims NHTSA was already aware of all of these incidents either from the agency's own records or from the company's notification outside of the EWR process. Unfortunately, this problem could have been stopped much sooner. The issue was first brought to light in 2011 but didn't result in a followup. NHTSA advised the automaker of discrepancies in January 2012, and it still did nothing. This third-party audit wasn't commissioned until September 2014. "Honda acknowledges that it lacked the urgency needed to correct its problems on a timely basis," it says in the announcement. Separately, the Japanese government is starting an investigation, as well. According to Reuters, the Japanese Transport Minister has created a task force to look into the Takata recalls and find out whether Honda under-reported incidents there. Scroll down to read the company's entire statement on the third-party investigation.

Honda reveals IndyCar aero kit

The IndyCar Series is stepping into a new era of competition that won't quite see manufacturers building their own chassis like they do in Formula One, but it's inching closer. This season, participating automakers will provide their customer teams not only with engines as they have in the past, but with complete aerodynamic packages. Chevy revealed its new aero kit last month, and now Honda – the only other automaker currently in the series – has followed suit with its own. Like Chevy's package, the new Honda kit is designed specifically for road courses and short ovals with a high degree of downforce that would hamper high-speed running around super speedways. The lower-drag package will likely be revealed sometime before the Indy 500 that will be the first speedway race on the calendar when it kicks off in May. The design of the package is a result of what Honda describes as an exhaustive development process that borrowed from the company's experience with Le Mans prototypes. It started out using CAD and CFD software before being validated on simulators, tested in wind tunnels and run on track with participation from Andretti Autosport. The aerodynamic appendages will be affixed to the existing Dallara chassis and powered by Honda's V6 engines, allowing individual teams to tweak the elements to their own requirements. With the manufacturers now allowed a greater degree of participation, series organizers will undoubtedly be hoping for more of them to join in on the action. The last time there were more than two automakers participating was in 2005, before Toyota pulled out. Ford was the sole engine supplier in the Champ Car series from 2003 until the series reunited with the Indy Racing League to form the current IndyCar Series. Honda Unveils 2015 IndyCar Series Aero Kits Mar 9, 2015 - TORRANCE, Calif. - Road Course/Short Oval package shown - Efficient development utilized CFD and multiple simulation tools - Wide range of aerodynamic tuning options available to teams Honda today debuted the package of aerodynamic upgrades and components its teams will use in the 2015 Verizon IndyCar Series, as the manufacturer seeks to add to an already impressive list of accomplishments in American open-wheel racing. The 2015 Honda Indy car "aero kit", produced by Honda Performance Development, Honda's racing arm in North America, includes nearly 200 individual pieces that can be fitted to the existing Honda-powered Dallara Indy car chassis.

Honda planning a second Vezel for developing markets

The new Honda Vezel was designed as a global product. Unveiled at the Tokyo Motor Show in November, the compact crossover is already going on sale in Japan, will soon reach Europe and will eventually hit the North American market as well - albeit with a different name and engine lineup. But it won't be sold everywhere.
According to Autocar India, the Vezel was originally earmarked to reach the emerging market on the subcontinent, but the declining value of the rupee has apparently forced Honda to rethink its strategy. Instead, the Japanese automaker is now expected to develop a second compact crossover - one more cost-effective to produce locally - for sale in India and other, nearby developing markets.
The new model would be based on the Brio, a hatchback that's smaller than the Fit (on which the Vezel is based) and built in India, Thailand and Indonesia. Honda has already enlarged the Brio's platform to create the Amaze sedan and Mobilio minivan. Building a crossover on the same platform would reportedly require some re-engineering - particularly around the wheel wells - but would apparently still be more cost-effective than importing the Vezel.