Xl Bluetooth Heated Leather Seating Backup Camera Remote Start Factory Warranty on 2040-cars

Auto blog

2019 GMC Sierra 1500 prototype shows off differences from Silverado

Now that the new Silverado has made its debut, we're awaiting the reveal of its mildly restyled twin, the GMC Sierra 1500. While it likely won't be that different as far as capability and major equipment are concerned, we are looking forward to seeing what design changes it will have. Based on these recent spy shots, the changes will be mild, but still enough to make it visually distinctive. One of the more obvious differences will be in the front fascia treatment. Unlike the Silverado's grille that's level with the top of the headlights, the GMC's will rise above the lights, which will also yield a slight drop on each side of the hood to meet the lights. The grille is quite tall, extending far below the headlights, too. We can make out, behind some mesh, two dips on the outer edges of the grille that give the Sierra a more menacing frown. Large foglights are also found right near where the scoops for the wheel air curtains, and the headlights are unified on the edges, rather than split on the Silverado. Along the sides, the sheet metal looks relatively unchanged. At some angles, we can make out the distinctive shoulder line from the Silverado that runs up to about the rear mirrors where it stops to make room for another crease that rises up from somewhere in the middle of the front doors to lead to the front. The wheel arches are decidedly different from the Silverado's though. While the Silverado has fairly rounded arches, the Sierra's have a rear-slanted bevel to the fronts of the arches and a rounded 90-degree corner at the rears. There isn't much we can tell about the rear except for the taillights. They're quite large, and unlike the Silverado's, there aren't any areas where the sheet metal intrudes. It also appears that the tops of the taillights extend farther forward into the bed sides than the Chevy's. Because the Sierra has almost always been a mechanical twin of the Silverado, we expect it to offer the same 5.3-liter and 6.2-liter V8s, as well as the new 3.0-liter diesel inline-6. Also, being a GMC, it will likely have a flashy, chrome-laden Denali trim level. We also will see the fully revealed model soon, as Automotive News reports the debut will be on March 1. Related Video: Featured Gallery 2019 GMC Sierra 1500 spy shots View 39 Photos News Source: Automotive News Spy Photos GMC Truck chevrolet silverado

2020 Ford Escape hybrids vs other crossover fuel sippers: How they compare on paper

Along with a new generation of Escape, Ford also reintroduced the world to the 2020 Ford Escape Hybrid. And if that weren't enough, Ford is adding a plug-in hybrid version. This is a sign of the times: people are more crossover crazy than ever, but are also seeking ways to use less fuel, whether it's for environmental or purely money-motivated reasons. The Ford hybrids aren't the only fuel-efficient compact crossovers on the market. They will be going head-to-head with conventional hybrids including the 2019 Kia Niro, 2019 Nissan Rogue Hybrid and 2019 Toyota RAV4 Hybrid. There are other plug-in hybrids including the 2019 Subaru Crosstrek PHEV, 2019 Mitsubishi Outlander PHEV and the plug-in version of the 2019 Kia Niro. There are even a couple diesels in the form of the 2019 Chevy Equinox and 2019 GMC Terrain. So we've rounded up the details on all these crossovers to see who leads and lags in criteria such as power, fuel efficiency, space and price. Check out all their details below. 2019 Subaru Crosstrek Hybrid View 68 Photos How do their engines and fuel economy compare? Conventional Hybrids and Diesels Let's face it, if you're buying one of these crossovers, one of the things that matters most to you is just how frugal with fuel they are. We'll start off with the conventional hybrids and diesels, and the clear victor is the Kia Niro, which in base FE trim, manages to hit 50 mpg combined. This is thanks to it sharing its powertrain with the Hyundai Ioniq, the Hyundai equivalent of the Toyota Prius. Buyers should take note that only the FE returns such high fuel economy. The LX and EX drop to 49 mpg, and the S Touring and Touring get 43. Even then, the least efficient Niro is the most efficient of the normal hybrids and diesels. It is nearly the least powerful, though, with 139 horsepower. Just behind it is the Toyota RAV4 Hybrid. It delivers 40 mpg combined, and it has an ace up its sleeve: it comes standard with all-wheel drive. Every other vehicle in this powertrain group has front drive standard, and the Niro isn't available with all-wheel drive at all. If that weren't enough, the RAV4 Hybrid also boasts the most power at 219 horses. While we can't say anything about Escape Hybrid fuel economy, we do know that it will make 198 horsepower, which is close to the class-leading RAV4. The least powerful of these is the Equinox and Terrain, and they return the worst fuel economy at 32 mpg.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.