Denali Package In Pewter And Matching Interior, Excellent Condition, Runs Great on 2040-cars

Auto blog

GM profits threatened by glut of pickups

Automotive News reports that General Motors may slash production or ramp up discounts in order to deal with an oversupply of pickup trucks. GM currently has more than double the standard supply of pickups, and the vehicles are threatening to dampen the automaker's profits for 2013. Typically, automakers try to sustain a 60- to 75-day supply of vehicles, but GM is currently loaded with a 139-day supply, as of last month. At the end of November, the automaker was sitting on 245,853 units.
The manufacturer says that it will adjust production accordingly before laying any incentives on the profitable pickups. Even so, there's some concern that the inventory swell could hurt the roll-out of the next-generation Chevrolet Silverado and GMC Sierra. GM actually began slowly stepping back production in August, but it's clear the company will take further action as it heads toward the end of the year and into the next. Analysts predict the automaker could reduce pickup manufacturing by nearly half in the first quarter of 2013.
That still may not be enough to keep GM from laying extra cash on the Silverado and GMC Sierra. While the company's incentive spending was down in November compared to the same month in 2011, both the Ram 1500 and Ford F-150 saw double-digit percentage increases in sales last month while the Silverado and Sierra numbers slid compared to a year prior. Incentive spending could help move more trucks and add some balance to the GM inventory surge.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Chevy Colorado, GMC Canyon get updated tachometers due to graphical error

After James Bearing bought a Chevrolet Colorado, he noticed a discrepancy between the truck's spec sheet and the truck's tachometer: Chevrolet said 3.6-liter V6 in the little pickup produces 305 horsepower at 6,800 rpm, but the the tachometer indicates a redline at 6,500 rpm. So either he wasn't making as much power as he was promised, or the tachometer display was incorrect. Bearing said he asked Chevy about it but got no response. Until now. A General Motors spokesman said the rev limiter is indeed set for 6,800 rpm, but the tach graphics "are slightly off" in the Colorado and the GMC Canyon, and submitted an SAE horsepower certification to back him up. If you're wondering how such a thing got past quality control... well, let's just say you're not alone. GM is going to fix "the graphics on future trucks," which makes it sound like Bearing will just have to learn to live with the indicated redline he's got. He could always pretend he's driving a sleeper, with four more ponies waiting to be unlocked in the danger zone for those who dare. Related Video: Featured Gallery 2015 Chevrolet Colorado: First Drive View 38 Photos Related Gallery 2015 GMC Canyon: Quick Spin View 27 Photos News Source: Auto Guide Auto News Chevrolet GM GMC Truck gmc canyon