2024 Gmc Yukon At4 on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM recalls 83,572 SUVs for ignition switch issue

General Motors is recalling 83,572 SUVs from the 2011 and 2012 model years over a potential ignition lock actuator issue. In affected vehicles, the actuator isn't the right size, which could cause the ignition to get stuck in the "Start" position, and then either due to a jarring event or a "cool interior temperature" the ignition could switch back to the "Accessory" position. Doing so would cause a loss of power assistance and the airbags might not deploy. This is a different ignition issue than the one that's been ongoing for the past year. GM said it expects that less than 500 vehicles suffer from the problem, but that the pool could include vehicles from 2007 through to 2014 that have already been fixed, but with defective parts. The 2011-2012 SUVs included in the National Highway Traffic Safety Administration notice: Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. GM will notify owners and dealers will inspect the ignition lock housing to see if it needs a free replacement. RECALL Subject : Ignition Lock Actuator may Bind Report Receipt Date: DEC 30, 2014 NHTSA Campaign Number: 14V827000 Component(s): ELECTRICAL SYSTEM Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2011-2012 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. In the affected vehicles, the ignition lock actuator may bind, making turning the key difficult or causing the ignition to get stuck in the "Start" position. CONSEQUENCE: If stuck in the "Start" position, the ignition may suddenly snap back into the "Accessory" position, causing a loss of engine, steering, and braking power, increasing the risk of a vehicle crash. If the vehicle is in a crash, the air bags may not deploy, increasing the risk of occupant injury. REMEDY: GM will notify owners, and dealers will inspect and replace the ignition lock housing, as necessary, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact GM customer service at 1-800-458-8006 (Cadillac), 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14696 for the original equipment, and 14912 for the service replacement parts.

GMC rules out subcompact crossover to go premium, focus on trucks

Don't wait for GMC's on-again, off-again baby crossover any longer. The company confirmed it has no plans to enter the growing car-based subcompact crossover segment in the near future because the expansion wouldn't fit its image. "I'm going to give you a definitive no on that one," answered Mark Alger, a regional marketing manager for GMC's Canadian division, when asked about the entry-level segment by GM Authority. "We want to position GMC as a premium brand, focus on our trucks, and capitalize on the AT4 name," he added. Positioning GMC as a premium brand wouldn't prevent officials from giving an entry-level the green light; Audi, BMW, and Mercedes-Benz all sell cars priced in the vicinity of $30,000. Focusing on trucks like the Sierra and the Canyon makes sense, however, because they compete in a bigger segment of the market where profit margins are much wider. It helps that GMC doesn't have to worry about markets outside of North America; it's not concerned about its sales and image in, say, Spain. We've heard speculation about GMC's entry-level model since the Granite concept (pictured above) made its debut during the 2010 Detroit auto show. It was approved for production in 2010, approved again the following year (complete with rear suicide doors), and canceled in 2012, but the reports never went away. The segment's popularity added credibility to the recent murmurs describing a born-again Granite aimed at the Honda HR-V and the Toyota C-HR, among others. The Chevy Trax and Buick Encore are both GM vehicles that compete in this segment.  GMC also canceled a body-on-frame, Bronco-taming SUV, according to a recent report. The truck-focused automaker promised every nameplate in its range will receive the rugged AT4 treatment by 2021, however, and it announced plans to show the off-road-ready Canyon in early 2020.