1991 Gmc Sonoma 1991 Gmc Sonoma Short Bed V8 on 2040-cars

Auto blog

GM warning 800,000 owners that their cars may need oil changes more frequently than they say

The days of changing your engine oil every 3,000 miles are long gone thanks to most cars having automatic oil monitoring systems, but about 800,000 General Motors vehicles apparently have incorrect monitoring software that is leading to premature engine component wear. According to Autoweek, certain 2010-2012 Buick LaCrosse, Regal, Chevrolet Equinox and GMC Terrain models equipped with 2.4-liter four-cylinder engines could be going too long in between oil changes resulting in a higher-than-normal number of warranty claims for the engine's balance chain. The balance chain links the balance shaft to the crankshaft, and a worn one can produce higher noise levels.
As a fix, GM dealers will be reprogramming the software for the monitors in an effort to reduce the interval between oil changes, which varies based on driving habits and conditions. Through February 2015, the software update will be done at no cost to vehicle owners, but since this is not a recall, after that point, it will be up to the discretion of dealers as to whether or not they will charge for the service. What isn't immediately clear is whether GM plans on giving assistance to out-of-warranty customers who are experiencing engine issues from the worn chain.

GM SUV window switch recall urges owners to park vehicles outside

It's not unusual for there to be a lag between an automaker announcing a recall and the official documentation showing up on the National Highway Traffic Safety Administration website. So it's no surprise that a recent GM campaign took about a month to appear in its official capacity. However, there appears to be some big differences between the two reports with potential safety implications.
In late June, GM announced that it needed to recall 181,984 examples of the Chevrolet Trailblazer, Buick Rainier, GMC Envoy, Isuzu Ascender and Saab 9-7x from the 2005-2007 model years, plus the 2006 Chevy Trailblazer EXT and 2006 GMC Envoy XL. The new documents paint a slightly different picture with 184,611 needing repaired and different model years listed.
The reason for the fix is still the same, though. It's possible for fluid to contact the master power window switch module in the driver's door, which can corrode the part. Eventually this could cause a short circuit, leaving the buttons inoperable and potentially leading to a fire. But the new NHTSA documents add an important note: "A fire could occur even while the vehicle is not in use. As a precaution, owners are advised to park outside until the remedy has been made."

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck