Find or Sell Used Cars, Trucks, and SUVs in USA

Local Trade 6.6l Duramax Diesel With Allison Transmisson on 2040-cars

Year:2005 Mileage:96665 Color: Gray
Location:

Washington, North Carolina, United States

Washington, North Carolina, United States

Auto Services in North Carolina

Wilburn Auto Body Shop-Mooresville ★★★★★

Automobile Body Repairing & Painting
Address: 264 W Plaza Dr, Denver
Phone: (704) 469-4468

Westover Lawn Mower Service ★★★★★

Automobile Parts & Supplies, Gasoline Engines, Automobile Accessories
Address: 2856 Westover Dr, Providence
Phone: (434) 822-0138

Truck Alterations ★★★★★

Automobile Parts & Supplies, Window Tinting, Truck Accessories
Address: 716 Smoky Park Hwy, Chimney-Rock
Phone: (828) 633-2600

Troy Auto Sales ★★★★★

New Car Dealers, Used Car Dealers, Wholesale Used Car Dealers
Address: 100 N Lee Ave, Four-Oaks
Phone: (910) 892-7373

Thee Car Lot ★★★★★

Used Car Dealers
Address: 2498 Gillespie St, Autryville
Phone: (910) 485-0077

T&E Tires and Service ★★★★★

Auto Repair & Service, Automobile Diagnostic Service
Address: 2925 Eastway Dr, Charlotte
Phone: (704) 531-8095

Auto blog

GMC shows how the 2022 Hummer could have looked even more futuristic

Fri, Oct 23 2020

Excitement filled the room when GMC asked its designers to resurrect the Hummer in April 2019, but a tinge of uneasiness permeated the department after executives locked in an early 2020 unveiling date. Luckily, stylists knew what they wanted early on in the development phase, and preliminary design sketches give us a fascinating look at how they shaped the electric off-roader that ended up making its global debut online in October 2020. Hummer, the brand, unceremoniously shut down in 2010 after General Motors failed to sell it to the Chinese, but its design DNA was so strong that stylists were able to pick up where their predecessors left off. All of the sketches published on Instagram by the official General Motors Design account show a boxy truck with a tall front end, a short windshield, and a generous amount of ground clearance. These styling cues trace their roots to the AM General Humvee that entered production in 1984 and made its combat debut when the United States invaded Panama in 1989. Even the wildest drawings still depict a pickup that's immediately recognizable as a Hummer. Most of the early design sketches wear some variation of the seven-slot grille that characterized Hummer's production models; it's a styling cue that hints at a heritage shared with Jeep under the American Motors Corporation (AMC) umbrella. Oddly, none wear the round headlights seen on the H2, the H3, and the HX concept that nearly became the H4. Was GMC afraid that its Hummer would end up looking too much like a Jeep? And, at least one sketch shows a fold-down windshield, a feature that will not make it to the assembly line. Sketches never reach production without modifications made in the name of packaging and safety concerns, and the Hummer is no exception, but stylists did a good job of reinventing the brand's design language without copying or erasing the past. If the company had stuck around long enough to make a second- and a third-generation H2, odds are it would look a lot like the GMC-branded model that will enter production in a year. GMC remains on track to start 2022 Hummer deliveries in late 2021, though it told Green Car Reports that it still hasn't built a fully functional prototype yet. When it arrives, this outdoorsy pickup will land in a burgeoning segment of the truck market that numerous models (including the Rivian R1T and Ford's electric F-150) will also call home.

NHTSA opens safety investigations into Toyota, GM and Honda crossovers

Fri, 08 Jun 2012

The National Highway Traffic Safety Administration is evidently keeping itself very busy these days, as the federal agency has just announced it is launching or renewing investigations into Toyota, Honda and General Motors crossovers.
2006-2008 model year Toyota RAV4 crossovers are under review for allegations of rear tie-rod rust which can result in failure. NHTSA also said it is probing some 35 complaints about 2005 Honda Pilot models with inappropriate activation of the vehicles' stability control system. The alleged malfunction can cause the vehicles to slow down or stop in bad unsafe situations. At the moment, NHTSA is reviewing a petition regarding the Pilot issue, a move that will determine whether it needs to open a full-blown investigation.
In addition, Saturn Outlook and GMC Acadia three-row crossovers built in 2007-2009 are getting looked at for "loss of low beam headlamp" function. One complainant said the wiring in his Outlook overheated and melted. NHTSA says it has received 415 complaints about the problem and a GM spokesman confirmed that the automaker already started a "Customer Satisfaction Program" in December to address the issue.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

Thu, Dec 7 2017

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck