2009 Gmc Savana 3500 16' Cube Box Damaged Rebuildable Wreck Clear Title on 2040-cars

Auto blog

2022 GMC Hummer Edition 1 weighs 9,063 pounds

From the beginning, the Hummer line of vehicles has been synonymous with the phrase, "absolute unit." The M998 Humvee turned to civilian use as the Hummer H1 came with a curb weight of 7,560 pounds depending on configuration. The much more urbane Hummer H2 didn't sacrifice much of those gains, putting about 6,615 on the scales. Let us not forget that the behemoth gravitational pull and square-jawed mass were what every Hummer buyer wanted. So, starting with the brand values and customer demand, and adding the fact that electric vehicles are substantially heavier than their ICE counterparts, no one should be surprised that the 2022 GMC Hummer Edition 1 weighs 9,063 pounds. That's just one of the substantial figures GMC included in a self-certification filing submitted to the U.S. Environmental Protection Agency, the document rooted out by Car and Driver. Last year GMC told us the Hummer would weigh 9,046 pounds, which proves again the Freshman 15 (or 16) is unavoidable.  Loaded up with humans and their accessories, the truck's gross vehicle weight rating (GVWR) comes in at 10,550 pounds. It takes a few other big numbers to keep that kind of tonnage on the go. The Ultium battery weighs 2,923 pounds. With a 617-amp-hour capacity at 400 volts, total capacity comes in at 246.8 kWh, specific energy at 158 Wh/kg. Usable capacity is about 85% less, at 212.7 kWh. For the time being, these numbers put every other pack in a production vehicle in the shade. That gargantuan chemical plant in the Hummer's floor powers a 329-mile range the same way a giant fuel tanks feed a truck that gets 8 miles to the gallon. The miles per gallon equivalent figures GMC submitted to the EPA are 51 MPGe city, 43 MPGe highway, 47 MPGe combined. Motor Trend questioned whether GM applied the correction factor used for window sticker numbers; if not, the standard 0.7 correction drops the MPGe specs to 36 city, 30 highway, and 33 combined. However, trucks with a GVWR beyond 8,500 pounds don't need to display fuel economy figures on their window stickers, so don't expect to see any such details on dealer lots. For comparison, the Rivian R1T Launch Edition weighs about 7,000 pounds, and fits a 128.9 kWh battery good for an estimated 314 miles estimated at 70 MPGe.

GM recalls 3,300 pickups and SUVs for new ignition-switch issue [UPDATE]

UPDATE: A statement from GM about the recall has been added below. The exact total of vehicles affected is 3,296, including 3,073 of them in the US. General Motors isn't letting an ignition-switch problem grow into a massive scandal again. The automaker is recalling about 3,300 North American trucks and SUVs. They are: the 2014 Chevrolet Silverado and GMC Sierra and the 2015 Chevy Suburban and Chevy Tahoe, as well as 2015 model heavy-duty pickups, the Detroit News reports, citing an Associated Press story. The issue appears to have been caught fairly quickly. In this case, the keys can get stuck in the "start" position and then slip to "accessory" if bumped. This is because the ignition lock gears have an outer diameter that's larger than the specifications allow. When that happens the engine shuts off, and the driver loses assistance to the steering and brakes. The airbags might also be affected. The vehicles get a new ignition-lock housing to fix the problem. According to the Detroit News, an employee who experienced the problem with the switch discovered the issue, and this person then let officials at the automaker know as part of the Speak Up for Safety program. A total of five reports of the fault were discovered. However, there are no cases of injuries or crashes. The claims to the automaker's resolution program eventually tallied that GM's previous ignition switch problem included 124 deaths and 275 injuries. The company also had to recall millions of vehicles and pay significant fines to the US government. GM Statement General Motors is recalling 3,073 full-size trucks from the 2014 and 2015 model years in the U.S. Some of these vehicles may have an ignition lock actuator gear with an outer diameter that exceeds specifications, which may make turning the ignition key difficult. The ignition key could get stuck in the "start" position. This may be more likely at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the "start" position, and the vehicle experiences a significant jarring event or the vehicle's interior temperature cools, the ignition lock cylinder could move out of the "start" position, rotate past the "run" position, and move into the "accessory" position, leading to loss of power steering assist, power brakes and potentially air bag deployment in certain crashes. Dealers will replace the ignition lock housing.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck