2014 Gmc Yukon Denali on 2040-cars

Auto blog

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.

2015 GMC Yukon erupts into flames during Anaheim test drive [w/video]

A 2015 GMC Yukon burst into flames while on a test drive in Anaheim, CA on Sunday after smoke filled the cabin. Residents of the neighborhood where the driver abandoned the redesigned Yukon reported hearing a series of small explosions (likely the tires, based on the video), according to a report from KTLA and The Los Angeles Times.
No one was injured in the incident, which The Times reports occurred after a possible oil or fluid leak. As you can see in the image above, the Yukon was engulfed in flames, although the Anaheim Fire Department was able to put out the blaze in about 15 minutes.
"We're very lucky that no one got hurt, and it was in an area that... was safe," Lt. Tim Schmidt of the Anaheim Police Department told KTLA reporters. "If there was any place that was going to be safe, it would be this area. It's very open. It worked out for us."

GM to squeeze out more production capacity for midsize trucks

General Motors was predicting a strong showing for the Chevrolet Colorado and GMC Canyon before they debuted, and demand among dealers for the midsize trucks even exceeded company's expectations. The positive situation has left GM with a problem, though: finding ways to increase capacity for the pickups at the Wentzville Assembly plant in Missiouri. With a third shift already running, GM has continued to look for ways to build just a few more of the trucks at the plant. The company has plans to hire as many as 1,000 more workers for the Saturday and Sunday shifts to construct an additional 2,000 pickups a month, according to unnamed insiders at the factory speaking to Automotive News. The little adjustments even extend to getting rid of an unpaid break to add 18 minute of assembly time over the course of a day, which equals about 3,500 more vehicles a year. All of this effort comes because the trucks are in such high demand. According to GM's figures, the company has delivered a combined 35,720 units of the Colorado and Canyon from January through April 2015, and the Chevy was the fastest-selling truck in the US for the previous three months. In May, it spent an average of just 12 days in showrooms before being snapped up. And even better for the company, 43 percent of these buyers came from other brands. According to Automotive News, the most popular trade-ins have included the Ford F-150, Toyota Tacoma, and Dodge Dakota. Related Video: