1993 Gmc Typhoon Jimmy -- Very Rare, Very Good Condition on 2040-cars

Auto blog

GM announces four new recalls, 507k vehicles affected

428,211 of these vehicles are located in the United States, 57,706 are in Canada, and 20,956 are in other markets. In its seemingly never-ending string of recalls, General Motors today announced four new campaigns covering some 506,873 vehicles. 428,211 of these vehicles are located in the United States, 57,706 are in Canada, and 20,956 are in other markets. First up is the 2013-14 Chevrolet Cruze, which is being recalled because "the inflator in the driver's front airbag may rupture and/or the airbag may not inflate during airbag deployment," according to GM. This could shoot metal pieces of the inflator into the cabin, injuring occupants during a crash. What's more, GM says that if the airbag does not inflate, this could, obviously, increase the risk of injury to the driver. A total of 29,019 Cruzes are affected in the United States, with an additional 4,066 units being recalled in Canada. The largest of the four recall campaigns involves four-wheel-drive versions of the 2014-15 Chevrolet Silverado and GMC Sierra, as well as the 2015 Chevy Tahoe, Suburban, GMC Yukon and Yukon XL. A grand total of 392,459 vehicles are affected in the US, with 53,607 more found in Canada, and an additional 20,874 in other markets. Here, the transfer case "may electronically switch to neutral without input from the driver," GM states. The automaker adds that if this occurs while the vehicle is moving, power will not be sent to the wheels. On top of that, if the vehicle is parked, it may roll away unexpectedly if the parking brake has not been set. In smaller recall news, 4,794 2013-14 Chevy Caprice police cars and SS sedans are being recalled in the US. According to GM, "If the motor gear teeth become stripped, the wipers may not operate" in these models. Lastly, 1,939 2014 Chevy Corvettes fitted with the FE1 or FE3 suspension are being recalled in the US "to repair a possible insufficient weld in the rear shocks that could lead to a fracture and/or reduce the shocks' service life." In Canada, 33 additional vehicles are affected, as are 82 more 'Vettes that were exported to other markets. General Motors is aware of one injury regarding the Cruze recall, and is not aware of any crashes or injuries in the other three recalls. Scroll down for the automaker's official release. GM Announces Four Vehicle Recalls DETROIT – General Motors (GM: NYSE) today announced four safety recalls covering 428,211 vehicles in the United States.

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.