2013 Gmc Terrain Sle 2 Sat Radio Bluetooth Rear Camera Power Equip Onstar 32 Mpg on 2040-cars

Auto blog

GM tells NHTSA pickup truck electronic glitch is 'inconsequential'

General Motors has been enduring some serious problems with recalls recently, and it is hoping to avoid launching another major safety campaign. 200,921 2014 Chevrolet Silverado and GMC Sierra pickups are under the microscope due to a rare problem with their instruments, an issue GM calls calls "inconsequential to motor vehicle safety." The Detroit-based automaker believes that the glitch is so minor that it has filed a petition with the National Highway Traffic Safety Administration asking the government safety watchdog for permission to pass on recalling the vehicles.
The fault at issue can occasionally cause the instrument cluster to reset when drivers use the steering wheel controls to browse songs from an external media device connected to the truck's USB ports. If a song's title information exceeds 2,000 bytes, according to The Detroit News, then the instrument panel can reset, which in turn causes the gauges, shift position indicator and cruise control telltale to turn off briefly. When rebooting, other instrument panel lights may briefly illuminate without their functions actually being activated. GM claims that if this does happen, the instrument display lights go out for about 1.5 seconds and the bulb check lasts a further five seconds. However, this snafu has no actual affect on the truck's operation. The glitch is present in trucks built between January 29, 2013, and October 28, 2013.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM recalling over 243,000 crossovers over possible seat belt defect

2010 Buick Enclave - Click above for high-res image gallery
The summer of 2010's recall hit parade continues unabated today, with General Motors having just announced that it is asking 243,403 owners of its 2009-2010 Lambda crossovers to bring their three-row haulers in for inspection. The culprit? Second-row seat belts in select Buick Enclave, Chevrolet Traverse, GMC Acadia, and Saturn Outlook CUVs have "failed to perform properly in a crash."
According to GM, a second-row seat-side trim piece is to blame, as it can impede the upward rotation of the buckle after the seat is folded flat. As a result, if the buckle makes contact with the seat frame, cosmetic damage can occur, potentially requiring additional force to operate the buckle properly. So far, no great shakes, but in the process of applying that additional force, the occupant may push the buckle cover down to the strap, potentially revealing and depressing the red release button. As a result of this, the belt may not latch, or in certain cases, it may actually appear to be latched when, in fact, it isn't.