2023 Gmc Sierra 1500 At4x on 2040-cars

Auto blog

GM tells owners not to use SUV wipers due to fire risk

General Motors is recalling 31,685 examples of the 2016 Buick Enclave, Chevrolet Traverse, and GMC Acadia because a short circuit in the windshield wiper motor can potentially lead to a fire. Due to the danger, the company is asking owners not to use the wipers until the problem is fixed, according to The Detroit Free Press citing the Associated Press. A manufacturing defect in the wiper motor cover means that the electrical terminals can come into contact and cause a short. The part could "melt, smoke, or catch fire," according to a statement from GM. The company will get them fixed immediately, and dealers will replace the cover. If there's bad weather at the time the owner specifies to get the recall work completed, the automaker will come pick up the crossovers. Depending on parts availability, the automaker will supply a rental car for customers, as well. The issue was discovered at the factory. According to the company's statement, only 6,405 actually made it to customers, and they were notified immediately by overnight letter. The rest were in dealer stock. The affected crossovers carry build dates between August 18, 2015 and September 24, 2015. Of those, there are 29,295 in the US and 1,073 in Canada. GM Statement: General Motors has told the National Highway Traffic Safety Administration that it will recall approximately 29,295 2016 model year Chevrolet Traverse, Buick Enclave and GMC Acadia SUVs in the U.S. because the front windshield wiper motor may overheat when in use because of a manufacturing defect. In some cases, the front windshield wiper motor cover may melt, smoke or catch fire. The approximately 6,405 customers who have taken delivery of these vehicles were notified by overnight letter and are urged to contact a GM dealer as soon as possible to arrange a service appointment. These customers should not use the front windshield wipers until they have been repaired. If weather conditions prevent driving the vehicle without using the windshield wipers, GM will arrange to pick up the vehicle for servicing. If repair parts are unavailable, GM will provide a rental car at no cost until parts become available. The total population, including Canada, Mexico and exports, is approximately 31,685. About 25,280 of these vehicles are in dealer stock and will not be sold until repairs are made.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

GM considering new powertrain options for large SUVs

Aside from the new General Motors offerings, there's not a whole lot of action going on in the fullsize SUV segment. That doesn't seem to be stopping GM from pushing the envelope in the market as Automotive News is reporting that the automaker is looking to introduce some new powertrain options into the Chevy Tahoe (and Suburban), GMC Yukon (and Yukon XL) and the Cadillac Escalade - all have been redesigned for the 2015 model year.
Now, we already know that GM and Ford are collaborating on nine- and ten-speed transmissions for a broad range of applications (including the big SUVs), but this new report says that GM is also considering other options as a way to one-up the competition and, of course, to optimize fuel economy. AN quotes Jeff Luke, executive chief engineer for GM trucks, as saying that "interesting powertrain technologies" are coming including a return of a hybrid SUV and possibly even a diesel engine. Although it sounds like the latter could come down to how customers respond to the 2014 Jeep Grand Cherokee EcoDiesel.