2011 Gmc Sierra Crew Z71 4x4 6-pass Tonneau Cover 42k!! Texas Direct Auto on 2040-cars

Auto blog

GM follows up Lambda CUV stop-sale with tire recall

In late January, General Motors announced a stop-sale for about 6,281 examples of the 2015 Chevrolet Traverse, GMC Acadia and Buick Enclave because of the possibility for the treads cracking on their 18-inch Goodyear Fortera HL tires. At the time, GM said that this would also eventually lead to a safety campaign to repair the problem, and the National Highway Traffic Safety Administration has just published those details. GM's recall covers 5,876 of the three Lambda platform crossovers to replace their tires. According to NHTSA, if the treads crack, there could be a loss of pressure and possible failure. Goodyear already announced its own recall of the tires after internal testing found small tread cracks. The company did not believe this was safety issue, but the problem did put the rubber out of compliance with federal laws. The business's safety campaign covered an estimated 48,512 tires. Of those, around 32,000 were reportedly made for GM to either be fitted to vehicles or sold as replacements. The remainder went to the aftermarket. Goodyear's portion of the recall is expected to begin around February 20. RECALL Subject : Tire Tread Cracking/FMVSS 110 Report Receipt Date: JAN 28, 2015 NHTSA Campaign Number: 15V044000 Component(s): TIRES Potential Number of Units Affected: 5,876 All Products Associated with this Recall Vehicle Make Model Model Year(s) BUICK ENCLAVE 2015 CHEVROLET TRAVERSE 2015 GMC ACADIA 2015 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2015 Buick Enclave vehicles manufactured December 9, 2014, to January 14, 2015, 2015 Chevrolet Traverse vehicles manufactured December 9, 2014, to January 20, 2015, and 2015 GMC Acadia vehicles manufactured December 9, 2014, to January 16, 2015, and all equipped with Goodyear P255/65R18 Fortera HL tires. These vehicles are equipped with tires that may experience tread cracking. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 110, "Tire Selection and Rims and Motor Home/Recreation Vehicle Trailer Load Carrying Capacity Information for Motor Vehicles with a GVWR of 4,536 kilograms (10,000 pounds) or Less." CONSEQUENCE: If the tire treads crack, a loss of tire pressure and possible tire failure may result, increasing the risk of a crash. REMEDY: GM will notify owners, and dealers will replace the tires that were manufactured within a specific date range, free of charge.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

Chevy Colorado, GMC Canyon midsize pickup trucks to get diesel engines

The market for midsize pickup trucks has all but been abandoned in the US, but General Motors is about to shake the market up with the all-new (to the US) Chevrolet Colorado and GMC Canyon. Launching next year, GM already told us that its new trucks would be a "fuel-efficient alternative" to fullsize trucks, and aside from the smaller size, Automotive News says that these trucks will accomplish this with a diesel engine.
According to the AN report, the next-gen Colorado and Canyon will offer a small, four-cylinder Duramax turbo diesel with a displacement of either 2.5 or 2.8 liters - both engines are currently used in this truck for other markets. This would allow GM to join the Cummins-powered Nissan Titan and Ram 1500 EcoDiesel as the only non-HD trucks in the US to offer diesel. The article goes on to say that the diesel versions of the Colorado and Canyon would launch about a year after the trucks go into production in fall of 2014.