2005 Gmc Sierra 1500 C1500 on 2040-cars

Auto blog

General Motors Recall List

It seems General Motors can't go more than a few weeks without issuing a major recall. Since the initial ignition lock recall on February 10, over 25 million vehicles have been recalled for defects. It seems General Motors can't go more than a few weeks without issuing a major recall. Since the initial ignition lock recall on February 10, over 25 million vehicles have been recalled for defects. We used the National Highway Traffic Safety Administration recall list to compile a snapshot of all the GM vehicles recalled in the last two months. NHTSA also provides a search engine that allows owners to search for recalls on their vehicle. An automotive company must do everything in their power to notify its customers when a recall is issued on a vehicle. If you own any of the following vehicles and you have questions regarding your car, you can contact Chevrolet at 1-866-694-6546, GMC at 1-866-996-9463, Buick at 1-800-521-7300 and Cadillac at 1-866-982-2339. Or check out General Motor's recall site. Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153) or go to www.safercar.gov. Here's a brief summery of the other vehicles currently under recall: July 26 – 414,333 cars affected NHTSA Campaign Number: 14V447000 Models under recall: Certain model year 2011-2012 Buick LaCrosse, Regal and Chevrolet Camaro, as well as certain 2010-2012 Cadillac SRX, Chevrolet Equinox and GMC Terrain vehicles, equipped with power height adjustable driver and passenger seats. Problem: In the affected vehicles, the bolt that secures the driver's and passenger's power front seat height adjuster may fall out causing the seat to drop suddenly to the lowest vertical position. Consequence: If the driver's seat unexpectedly drops, the distraction and altered seat position may affect the drivers' control of the vehicle, increasing the risk of a crash. Solution: Dealers will replace the height adjuster shoulder bolts, free of charge. July 14 – 16,939 cars affected NHTSA Campaign Number: 14V341000 Models under recall: Certain model year 2011 Cadillac CTS vehicles manufactured October 18, 2010, to June 2, 2011. Problem: In the affected vehicles, vibrations from the drive shaft may cause the vehicle's roll over sensor to command the roof rail air bags to deploy. Consequence: If the roof rail air bags deploy unexpectedly, there is an increased risk of crash and injury to the occupants.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

GM updating fullsize pickups for 2015

As Ford prepares to hit the market with its x-factor, aluminum-intensive F-150 and Ram sales stand tall enough to meet General Motors truck sales eye-to-eye, GM is putting the word out that it's going to add more features to its trucks and do so more regularly. An executive engineer for pickups told reporters that "a whole array" of changes are on the way as soon as the 2015 model year and then would likely come "the year after that, the year after that, the year after that."
Only GM knows the way it plans to go with its fullsize trucks, with almost everyone else - including its dealers - griping about market share at the same time as they applaud profits and hope for clarity and growth. GM raised prices on the Chevrolet Silverado and GMC Sierra not long after launch even as it was losing market share and getting called "the least successful large pickup launch over the last 15 years," further upsetting dealers, then Ram outsold the Silverado in March of this year and led GM to increase incentives. But transaction prices rose with the premium; in the first quarter of this year more than 37 percent of the trucks costing more than $40,000 were the Silverado and Sierra, leading one dealer to say of the Sierra, "You can't sell a cheap one," and the analyst who made that "least successful launch" comment to opine, "GM may have made the right call to go for price over share."
We won't know for a few months what any of these updates will be, but the rumored changes for the Silverado and Sierra appear to cover all the bases, including appearance, capability and fuel economy. Rumors run to higher gear counts, stop-start technology and diesel engines before brand-new pickups come for the 2019 model year, those next-generation models supposedly to be engineered with a lot more aluminum.