2013 Gmc Acadia Sle on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM profits threatened by glut of pickups

Automotive News reports that General Motors may slash production or ramp up discounts in order to deal with an oversupply of pickup trucks. GM currently has more than double the standard supply of pickups, and the vehicles are threatening to dampen the automaker's profits for 2013. Typically, automakers try to sustain a 60- to 75-day supply of vehicles, but GM is currently loaded with a 139-day supply, as of last month. At the end of November, the automaker was sitting on 245,853 units.
The manufacturer says that it will adjust production accordingly before laying any incentives on the profitable pickups. Even so, there's some concern that the inventory swell could hurt the roll-out of the next-generation Chevrolet Silverado and GMC Sierra. GM actually began slowly stepping back production in August, but it's clear the company will take further action as it heads toward the end of the year and into the next. Analysts predict the automaker could reduce pickup manufacturing by nearly half in the first quarter of 2013.
That still may not be enough to keep GM from laying extra cash on the Silverado and GMC Sierra. While the company's incentive spending was down in November compared to the same month in 2011, both the Ram 1500 and Ford F-150 saw double-digit percentage increases in sales last month while the Silverado and Sierra numbers slid compared to a year prior. Incentive spending could help move more trucks and add some balance to the GM inventory surge.

2021 GMC Yukon will pull a 180 thanks to a Hurricane Turn feature

GMC isn't a hip, young startup, but its engineers are out to prove it's possible to teach an old dog new tricks. The next-generation Yukon will offer adventurers seeking a quick turn-around a "Hurricane Turn" feature that functions a lot like Rivian's Tank Turn technology. The two systems use different hardware to perform a similar action. We didn't hear anything about the Hurricane Turn feature during the Yukon's unveiling because GMC planned to keep it under wraps until later, but an eagle-eyed report at Motor Trend uncovered it and quizzed the firm. It's real, and it's engaged when the driver switches the stability control system off, energetically turns the steering wheel in either direction, and mashes the accelerator pedal to the floor. The Yukon needs to be on a loose surface, too. If you're turning right, the on-board computer applies braking power to the passenger-side wheels to prevent them from spinning, while the engine continues to turn the driver-side wheels to rotate the Yukon on its own axis. The exact opposite happens if you're turning left. It's clever and relatively simple; there's no extra hardware required to enable the feature, though it shows the next Yukon is far more advanced than its predecessor. It goes without saying that only four-wheel drive models will receive the Hurricane Turn feature. There's no word yet on whether it will be compatible with all three engine options, or if it will be limited to a certain trim level. GMC will publish additional details about the system, and hopefully a video of it in action, in the coming months. Rivian, on the other hand, leveraged its four-motor electric powertrain to teach the R1T (and presumably the R1S) how to pull a 180. The right wheels turn in the opposite directions as the left wheels – hence the name Tank Turn – to spin the truck around like a CD in a Walkman. Its system doesn't use the brakes. The 2021 Yukon is due in showrooms in the summer of 2020, and Amazon-funded Rivian won't start making the R1S until the end of 2020 at the earliest, so GMC will beat its younger rival to the punch. What remains to be seen is how often motorists use either function. We're betting not very once the initial novelty wears off. Related Video: