1977 Ford Thunderbird Runs And Looks Good .trans Slips Wire Wheels on 2040-cars

Auto blog

NHTSA investigating 500k Ford and Mercury cars for lighting failures

The Ford Crown Victoria and Mercury Grand Marquis might be long gone as new models in showrooms, but the National Highway Traffic Safety Administration might check them out yet again for a potential problem. At the urging of North Carolina Consumers Council, the agency may open another investigation into the front lighting control module on vehicles from the 2003-2005 model years, and NHTSA estimates the issue could affect 517,945 vehicles. If the module stops working, it can cause a complete failure of all forward lighting, including the headlights. NHTSA previously investigated the issue in 2008 and 2009 but found no need for a recall, according to Bloomberg. Ford also extended the warranty on the part to 15 years or 250,000 miles. To prompt this new request, the North Carolina Consumers Council received a letter from a woman experiencing the module's failure. Upon further investigation, the council found 604 complaints of this problem on NHTSA's website, including seven crashes. Furthermore, the group has alleged that dealers told customers that the parts to perform the replacement weren't available, despite the extended warranty. According to the government agency, "A defect petition has been opened to evaluate the issue and make a grant or deny decision." Ford spokesperson Kelli Felker tells Autoblog via email, "We will cooperate with NHTSA, as we always do." You can read the council's complete letter to the Feds in PDF format, here. INVESTIGATION Subject : Loss of headlamp/exterior lighting Date Investigation Opened: APR 01, 2015 Date Investigation Closed: Open NHTSA Action Number: DP15002 Component(s): EXTERIOR LIGHTING All Products Associated with this Investigation Vehicle Make Model Model Year(s) FORD CROWN VICTORIA 2003-2005 MERCURY GRAND MARQUIS 2003-2005 Details Manufacturer: Ford Motor Company SUMMARY: The Office of Defects Investigation (ODI) has received a petition from the North Carolina Consumers Council, Inc. requesting a defect investigation of an alleged defect condition resulting in headlight and/or exterior lighting failure on 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles. The petition letter is attached for review. The petitioner alleges a defect in the lighting control module that powers the headlights which can result in the loss of vehicle headlights and/or all exterior lighting while driving. ODI has previously investigated this issue under PE08-066 which was closed without a defect finding.

Ford, Samsung shack up to bring regen braking to non-hybrid models [w/video]

Ford must be desperate to get itself ready for the beach this summer because it is really trying to get into shape. Shortly after unveiling the Lightweight Concept that cut the weight of a Fusion down to that of a Fiesta, it's now the rest of the line's turn for improvement. The company is wrapping up a 10-year research project aimed at developing next-gen automotive batteries to improve efficiency.
Ford claims that 70 percent of its lineup will have stop/start tech by 2017. The key to this massive proliferation is its new dual-battery system that combines a lithium-ion battery with a lead-acid one and regenerative braking. The setup works by harvesting braking energy and converting it to electricity. When the vehicle stops, the engine shuts off, but the Li-ion battery has enough juice to keep the accessories running. The engine starts up again as drivers take their foot off the brake. The layout would mean less wasted gas while idling. It's already available on Ford hybrids and is somewhat similar to the i-Eloop capacitor-based system from Mazda.
The bigger challenge is tuning the regenerative braking right. While hybrid drivers may be a little more adventurous, when it comes to getting a hang of regen braking, conventional buyers might not be so open-minded. The systems have a tendency to be a little grabby at first and then taper off at very low speeds. Ford needs to make sure it's just right to avoid turning off buyers.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).