1955 Ford Thunderbird T-bird Barn Find on 2040-cars

Auto blog

Junkyard Gem: 1991 Mercury Grand Marquis LS

Ford's now-defunct Mercury Division first began using the Marquis name in 1967, on a sporty full-size hardtop based on the Ford LTD, then began offering the Grand Marquis beginning in the 1979 model year. These big, boxy luxury sedans were replaced by big, curvy luxury sedans (on the same platform) starting with the 1992 model year, so today's Junkyard Gem is one of the very last squared-off Grand Marquises ever built. The 1991 Grand Marquis (or "Grandma Keith," as many refer to it today) looks nearly identical to its 1979 predecessor at a glance, just as the 2011 model doesn't differ much from the 1992 model. Ford saw no reason to follow short-lived fashion trends with its simple, sturdy rear-wheel-drive sedan. Only two Grand Marquis trim levels were available for 1991: the base GS and the (somewhat) upscale LS. The former listed at $18,741 and the latter at $19,241, which comes to about $41,494 and $42,601, respectively, in inflated 2022 dollars). This interior would have seemed comfortingly familiar to a 1968 (or even 1958) Mercury owner time-traveling to 1991.  This is the optional "full grain leather seating surface," which cost an extra $489 (about $1,083 today). Dig those opera lights! Air conditioning was standard equipment in the 1991 Grand Marquis and its wagon counterpart, the Colony Park. The engine is the good old pushrod 5.0-liter Windsor V8, which would be replaced by a far more modern 4.6-liter SOHC mill in the '92 Grand Marquis. This engine was rated at 180 horsepower. A four-speed automatic was the only transmission available. The early 1990s ended up being the last gasp for padded vinyl roofs being considered mainstream equipment on new Detroit cars; this one was called the "Formal Coach" roof and cost an additional 725 bucks ($1,605 now). Such roofs were still available on a few cars later in the decade, but their time had passed. Why would such a clean Grandma Keith end up in a place like this? That's easy: it got T-boned directly into the right front wheel, mangling the body and bending up the suspension. This damage might have been worth fixing when the car was five years old, but it's a write-off when it happens to a 31-year-old Ford Panther. 1991 Mercury Grand Marquis Commercial - Savings Ad The granddaddy of them all, and on sale in South Texas! Related video: 2008 Mercury Mariner Hybrid test drive Autoblog

Ford recalling nearly 700k Escape CUVs, C-Max hybrids over two separate safety issues

Poor Escape. Ever since its launch in 2012, Ford's small CUV has been the subject of many, many, many recalls. And today, The Detroit News is reporting that Ford is adding two more recalls to the 2013-14 model year Escape's permanent record, one of them also involves the C-Max hybrid hatchback.
The first recall, covering 692,500 Escape and C-Max vehicles, is due to a software glitch that could cause the airbags - specifically, the safety canopy - to not deploy in a timely fashion during rollover crashes. According to the News, Ford says no crashes or injuries have been reported in relation to this problem.
The second recall, covering 692,700 Escapes, is related to the door handles. The News reports that the exterior door handles could open while the vehicle is in motion, and could also fail to latch properly. Once again, no crashes or injuries have occurred because of this. The National Highway Safety Traffic Administration has not issued an official notice on either recall as of this writing.

This is what a 3D-printed liquid metal Ford Torino looks like

Artist Ioan Florea has encapsulated a 1971 Ford Torino with 3-D-printed liquid metal transferred onto the car using technology that he developed, and the result is a stunningly shiny, seamless design.
"The surface has the highest coefficient of reflectivity never achieved before," Florea told us in an e-mail, using "nano-materials and nano-pigments that create an internal three-dimensional structure and dictate the polymer how to behave." Sure... We'll leave it to him to make any more 3-D-printed liquid metal-transferred art pieces.
Florea grew up in Romania, and the motivation behind picking the old Ford as his canvas came from his childhood memories of what an American car is - "big and wide and fascinating," he says - and the European name of the car itself, which it shares with an Italian city.