1987 Ford Mustang Gt Convertible 2-door 5.0l 5-speed Manual on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford Mustang GT500 successor spied near SVT

Details about the next-gen Ford Mustang are scarce, and there's even less information out there about the upcoming replacement for the Shelby GT500. Previously rumored to drop the Shelby name and wear the GT350 moniker, the highest-performance Mustang has just been spotted testing near Ford's SVT operations.
Despite being cloaked in heavy camouflage, we can instantly tell this prototype is different from other Mustang spy shots we've seen in the past. Aside from the Shelby-spec wheels, quad exhaust outlets (previous spy shots show only two) and beefier brakes, this car also has air intakes on the hood and front fenders. These elements help to neither prove nor dismiss rumors that the next SVT Mustang will be naturally aspirated. It also looks like Ford is may be planning some changes to this car's rear suspension, as there is some extra camouflage added beneath the rear end of this prototype.
As a bonus, these spy shots also give us our first look inside the new Mustang, revealing a new steering wheel (with more buttons) and a glimpse of the dual-pod instrument gauges. Check out past spy shots of the 2015 Mustang showing off its new face and driving around town.

Ford Focus RS ready to make our hot hatch dreams real

Ford's current hot hatch siblings the Fiesta ST and Focus ST are already two pretty great entries into the segment, but there's always a desire for a little more. Thankfully, it looks like the Blue Oval is ready to satiate that need because it's continuing to test the even more powerful Focus RS around Europe. According to our spy shooters, these shots come from near the Nürburgring.
As with previous photos, Ford engineers continue to heavily camouflage the front end of the RS prototypes, but there's a big difference here. Unlike earlier ones, this example appears to have a closer-to-production-ready front bumper rather than just a horizontal strip for the license plate. That may point to development getting somewhat closer to wrapping up. Although, this one lacks the larger rear wing from prior testers, and the exhaust also appears to be a work in progress with the rear diffuser covered in mesh in these latest shots.
The RS is rumored to be using the 2.3-liter turbocharged four-cylinder from the 2015 Mustang, but power is reportedly turned up from 310 horsepower in the 'Stang to somewhere between 325 hp and 350 hp for the Focus. Routing all that just through the front wheels could be a recipe for serious torque steer, and all-wheel drive is potentially being used for better traction.