1971 Ford Mustang on 2040-cars
Aurora, Connecticut, United States
Message me at : parrnell.rathay@aol.com This is a TRUE Boss 351, not a clone or tribute car. FULL California car. 1 of 1806 cars built. Engine was bored .030 over,balanced, ARP rod bolts, forged 11-1 pistons, Comp valve train using rollerrockers, Magnum push rods, Comp solid lifter cam, springs, locks and retainers,rods shot peened and the crank was ground 10/10. The 4 speed trans was rebuiltwith new syncros, bearings, seals, ect. Drive line was rebuilt with a new slipyolk and u-joints. The factory 3:91 Traction-Loc 31 spline axle rear end hasalso been gone through. New power steering, master cylinder, calipers, wheelcylinders, lines, pads and shoes.
Ford Mustang for Sale
- 1965 ford mustang gt(US $18,000.00)
- 2015 ford mustang(US $15,000.00)
- 1971 ford mustang boss 351(US $15,000.00)
- 2013 ford mustang laguna seca(US $21,000.00)
- Ford: mustang fast back(US $11,300.00)
- 1970 ford mustang boss 302 fastback(US $33,659.00)
Auto Services in Connecticut
Warburtons Automobile Repair ★★★★★
Vail Buick GMC ★★★★★
Saf-T Auto Ctr ★★★★★
Ren Sales & Svc ★★★★★
Pop`s Exhaust ★★★★★
Paul`s Automotive ★★★★★
Auto blog
Spy shooter claims proof of upcoming aluminum Ford F-Series Super Duty
Thu, 26 Jun 2014Ford has already confirmed that the 2015 F-150 (pictured above) was just the beginning for its more extensive use of aluminum. CEO Alan Mulally said it himself during the 2014 Detroit Auto Show. We've even already seen the future Raptor testing with an aluminum body. But a recent discovery from an intrepid spy photographer might indicate that the lightweight metal is coming to the Blue Oval's Super Duty pickups in their upcoming generation, as well.
According to Automotive News, a spy shooter in Colorado spotted a prototype for the next-gen F-350 testing. He happened to have a magnet on hand and got close enough to check the truck out. When he held it up to the metal in the bed, it didn't stick, which signaled to him a switch from steel to aluminum.
Obviously, this claim raises some questions. Given that it was a test vehicle, one possibility is that the Blue Oval is just evaluating the feasibility of switching to aluminum for the Super Duty trucks, not necessarily committed to it yet. Ford has been testing it quite exhaustively, after all. In fact, much of the rest of the truck in question was covered in camouflage, so it's possible that the magnet failed to work along the rest of the body not because it was aluminum, but because it wasn't powerful enough to get through the disguising material. Thus, the lightweight metal's use could be far less substantial than on the new F-150. Still, it was a clever idea for the cameraman to check things out and might have given us the first hint about brand's next heavy-duty models.
The next-generation wearable will be your car
Fri, Jan 8 2016This year's CES has had a heavy emphasis on the class of device known as the "wearable" – think about the Apple Watch, or Fitbit, if that's helpful. These devices usually piggyback off of a smartphone's hardware or some other data connection and utilize various onboard sensors and feedback devices to interact with the wearer. In the case of the Fitbit, it's health tracking through sensors that monitor your pulse and movement; for the Apple Watch and similar devices, it's all that and some more. Manufacturers seem to be developing a consensus that vehicles should be taking on some of a wearable's functionality. As evidenced by Volvo's newly announced tie-up with the Microsoft Band 2 fitness tracking wearable, car manufacturers are starting to explore how wearable devices will help drivers. The On Call app brings voice commands, spoken into the Band 2, into the mix. It'll allow you to pass an address from your smartphone's agenda right to your Volvo's nav system, or to preheat your car. Eventually, Volvo would like your car to learn things about your routines, and communicate back to you – or even, improvise to help you wake up earlier to avoid that traffic that might make you late. Do you need to buy a device, like the $249 Band 2, and always wear it to have these sorts of interactions with your car? Despite the emphasis on wearables, CES 2016 has also given us a glimmer of a vehicle future that cuts out the wearable middleman entirely. Take Audi's new Fit Driver project. The goal is to reduce driver stress levels, prevent driver fatigue, and provide a relaxing interior environment by adjusting cabin elements like seat massage, climate control, and even the interior lighting. While it focuses on a wearable device to monitor heart rate and skin temperature, the Audi itself will use on-board sensors to examine driving style and breathing rate as well as external conditions – the weather, traffic, that sort of thing. Could the seats measure skin temperature? Could the seatbelt measure heart rate? Seems like Audi might not need the wearable at all – the car's already doing most of the work. Whether there's a device on a driver's wrist or not, manufacturers seem to be developing a consensus that vehicles should be taking on some of a wearable's functionality.
1964 Ford GT40 prototype to be auctioned in April
Wed, 12 Mar 2014The Ford GT40 owns a firm spot on the list of the greatest American racecars ever made, being the first car from the United States to take an overall win in the 24 Hours of Le Mans. And now Mecum will auction what it claims is second-oldest GT40 still in existence at its Houston sale on April 12.
The story of the GT40 is fascinating. Henry Ford II attempted to buy Ferrari in the early '60s, but Enzo refused. Ford decided if he couldn't have them, then he would beat the Prancing Horse on the track. Ford went to Carroll Shelby and asked him to spearhead the program. The early cars combined a steel monocoque chassis with Ford's 4.2-liter V8 engine pumping out around 350 horsepower. The first prototype made its public debuted on April 1, 1964, at the New York Auto Show.
Shelby kept building prototypes, including GT/104, which is for sale here. This version featured a lighter steel chassis and was raced at Le Mans in 1964. However, a fire forced it to retire. It was then repainted and had a 4.7-liter (289-cubic-inch) engine fitted. The chassis had its best finish at the 1965 Daytona Continental 2,000 Kilometers where it finished third with Bob Bondurant and Ritchie Ginther behind the wheel. Later that season, it was shipped back to Ford where it was restored and displayed at auto shows until 1971 when the automaker sold it. Since then, it has had many private owners.