Find or Sell Used Cars, Trucks, and SUVs in USA

1967 1968 Mustang Fastback Good For Roof Rough Body Only! Ford Project Cars on 2040-cars

Year:1967 Mileage:0
Location:

Colchester, Connecticut, United States

Colchester, Connecticut, United States
Vehicle Title:Flood, Water Damage
Fuel Type:Gasoline
Engine:000 6
For Sale By:Private Seller
VIN: 7T02TXXXXXX Year: 1967
Drive Type: RWD
Make: Ford
Mileage: 0
Model: Mustang
Trim: FASTBACK
Condition: Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. ... 

Auto Services in Connecticut

Yale`s Inc ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Automobile Parts & Supplies-Used & Rebuilt-Wholesale & Manufacturers
Address: 430 Maple Ave, Gilman
Phone: (860) 848-9245

Spotless Detail ★★★★★

Auto Repair & Service, Automobile Body Repairing & Painting, Automobile Restoration-Antique & Classic
Address: 34 Winding Lane, New-Canaan
Phone: (914) 218-3300

South Green Automotive ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Automotive Tune Up Service
Address: 880 Wethersfield Ave, Windsor-Locks
Phone: (860) 296-2616

Sears Auto Center ★★★★★

Automobile Parts & Supplies, Tire Dealers
Address: 545 Washington St, Southington
Phone: (860) 854-6000

Safe & Sound Inc ★★★★★

Automobile Parts & Supplies, Automobile Radios & Stereo Systems, Consumer Electronics
Address: 428 East St, Somers
Phone: (413) 594-6460

Redan Auto Upholstery Co ★★★★★

Automobile Parts & Supplies, Automobile Seat Covers, Tops & Upholstery, Upholsterers
Address: 365 E Cedar St, Newington
Phone: (860) 666-4005

Auto blog

Ford dealers offered discounts on tools to fix aluminum

Mon, 27 Jan 2014

With the introduction of the aluminum-bodied 2015 Ford F-150 (and the likely use of aluminum in future Ford products), Ford is looking to help its dealerships reduce costs related to repairing this more labor-intensive material. Automotive News is reporting that Ford dealers with body shops will require an estimated $30,000 to $50,000 in equipment and training to work on aluminum, and to help alleviate the financial burden of the new F-150, Ford has announced a special 20-percent discount on this equipment.
Dealers will be able to save up to $10,000 on tools such as welders, air-filtration systems and rivet guns and to create aluminum-specific work stations. The new F-150 goes on sale in the fourth quarter, and dealers have until October 31 to take advantage of this deal, according to the report.

J Mays on the 2015 Ford Mustang

Thu, 05 Dec 2013

J Mays, head of design at Ford, may be retiring from the company after 16 years, but not before showing the world his swan song: the 2015 Mustang. Ford officially revealed its new coupe and convertible to the public at events around the world on Thursday, including a live unveiling on ABC's Good Morning America, and Mays was in attendance at the automaker's home event in Dearborn, MI, which is where we caught up with him for a few words about his new baby.
"It's a joy" to design the Mustang, Mays told Autoblog, adding that this sixth-generation coupe is his "favorite design so far." Of course, the 2015 model takes cues from all of the generations that came before it, but Mays said it was important to edit down the specific elements from previous models, leaving just enough off to let the customer "participate and fill in the blanks."
"If it doesn't sell itself, you probably aren't a Mustang fan."

Rising aluminum costs cut into Ford's profit

Wed, Jan 24 2018

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.