Find or Sell Used Cars, Trucks, and SUVs in USA

1923 Ford Model T Hot Rod! on 2040-cars

Year:1923 Mileage:54864
Location:

The car is a fiberglass custom build that was passed down from my father, built in the 80's registered as a 1923 ford model T the registration is current. It has a 327 motor  with offenhauser high rise intake two Holley 4 barrel carbs and straight pipe headers. 4 speed automatic transmission. custom pearl yellow paint with pin striping. new fuel pump and filter, new front tires, new oil change and filter, all electrical is good to go minus the battery itself. fresh radiator flush. the car sounds like a drag racer at the starting line. A person with the love of horsepower is gonna really love this thing. the carburetors need to be rebuilt and the back shelf that covers the gas tank is missing but other than those two things it is a complete little hot rod. i have set the reserve price lower to compensate the buyer for the cost of two carb rebuilds the battery and that rear shelf. i'm out of the country on deployment so i cant take phone calls or texts about the car but i will answer any questions through email. it does have a detachable top also that is not shown. buyer is responsible for pick up of the vehicle.

Auto blog

Ford opens the doors on its Swedish rally skunkworks

Fri, 19 Sep 2014

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

NHTSA closes investigations into Ford Taurus, Hyundai Santa Fe

Wed, 03 Jul 2013

Ford and Hyundai are out from under the scrutinizing eyes of the National Highway Traffic Safety Administration after the government agency said it was closing investigations against both automakers over vehicle safety concerns.
Ford was being investigated for reported damaged speed control cables on Ford Taurus (shown above) and Mercury Sable models, both built between 2000 and 2003. Vehicles with the company's Duratec engines allegedly failed to allow owners to brake as expected. Owners lodged 100 complaints and were involved in five accidents, according to NHTSA records. The American automaker responded to the reports, and on June 21 of this year, said that it would inspect and repair all affected vehicles, regardless of the mileage.
Hyundai was under investigation for a reported loose fastener on the steering shaft of its 2011 Santa Fe (shown in the gallery below). After NHTSA launched its inquiry, the Korean automaker responded with its own investigation that yielded four affected vehicles. Following the inspection of 680 vehicles at its assembly plant, Hyundai said the issue was due to employee error and that no further defects have been found.

Ford, GM still doing new business with Takata amidst airbag crisis

Thu, Nov 20 2014

Lengthy vehicle development times make it difficult for automakers to cut and run from the supplier. You might expect automakers to be fleeing any connection with beleaguered supplier Takata in the wake of the company's exploding airbag inflator crisis. After all, with a Senate hearing, pending lawsuit, plummeting stock value and demand for a national recall, the tier-one supplier isn't at its strongest right now. However, years of cooperation mean that automakers are standing by Takata, and necessity may be playing a role, as well. About 39 percent of Takata's business comes from airbags, and seatbelts make up another significant chunk of the operation too, says Bloomberg. The long-term relationships and lengthy vehicle development times make it difficult for automakers to cut and run from the supplier. "Takata has so much product breadth that I don't really see that they could just disappear," said AutoPacific analyst Dave Sullivan to Bloomberg. For example, Takata helped develop the unique front center airbag with General Motors in models like the Chevrolet Traverse and Buick Enclave. Outside of safety tech, it is also a partner with Ford on the adaptive steering system available on the upcoming 2015 Edge. These long-lasting partnerships make change difficult now that there's a problem. According to Reuters, automakers claim it would take a year or longer to set up with a different supplier for replacement airbag inflators. Switching to a completely different part for the repairs might not be a viable option either, because of the engineering time needed. BMW is taking action, though. According to Reuters, the Bavarian brand is working with the supplier to move inflator production from Monclova, Mexico, to a Takata factory in Freiburg, Germany. The Mexican plant may be the source of some of the faulty parts. News Source: Bloomberg, ReutersImage Credit: Jens Meyer / AP Photo BMW Ford GM Safety Takata airbag recall