2014 Ford Fusion Se on 2040-cars

Auto blog

Ford Recalling 70k Escape and Mariner Hybrids for cooling issue

Ford is recalling about 70,209 examples of the 2005-2008 Ford Escape Hybrid and the 2006-2008 Mercury Mariner Hybrid because the cooling pumps for their hybrid systems could fail.
According to the company's defect notice, it's possible for the original "Motor Electronics Coolant (MEC) Pump" to wear out and fail, which would could cause the hybrid system to overheat. If this happens, the vehicle goes into a safety mode that takes away most or all of its power. However, braking and steering still operate normally. After cooling down, the affected models restart normally. The company says that it's not aware of any accidents or injuries related to this problem.
Ford will begin repairing the vehicles in late October, and dealers will be installing improved, brushless pumps on the affected models at no charge to owners. If drivers had their pumps fail before this recall, they can contact Ford for a possible reimbursement. Scroll down to read the recall announcement from the National Highway Traffic Safety Administration or download the full defect notice as a PDF, here.

Ford Mustang, F-150, Expedition, and Lincoln Navigator recalled

The Basics: Ford will recall 201,900 examples of the 2011-2012 F-150, 2012 Expedition, 2012 Mustang, and 2012 Lincoln Navigator. The affected vehicles have the 6R80 transmission. Of the total, there are 84,000 of them in the United States and 17,900 in Canada. The Problem: The output speed sensor on the vehicle's transmission lead frame can force the gearbox to downshift into first gear. If this happens at high speed, it could cause the rear tires to slide or lock up. Injuries/Deaths: There are no reported injuries, but Ford know of three accidents related to this problem. The Fix: Dealers will update the powertrain control module software to eliminate the problem, and they'll also replace the transmission lead frame. If You Own One: Ford will begin notifying affected customers by mail on May 23. Related Video: FORD MOTOR COMPANY ISSUES THREE SAFETY RECALLS AND TWO SAFETY COMPLIANCE RECALLS IN NORTH AMERICA DEARBORN, Mich., April 27, 2016 – Ford Motor Company is issuing three safety recalls and two safety compliance recalls in North America. Details are as follows: Ford issues safety recall and customer satisfaction program for certain 2011-2012 Ford F-150, and 2012 Ford Expedition, Ford Mustang and Lincoln Navigator vehicles in North America to update powertrain control module software and inspect for certain diagnostic trouble codes Ford is issuing a safety recall for approximately 202,000 2011-2012 Ford F-150, and 2012 Ford Expedition, Ford Mustang and Lincoln Navigator vehicles for a potential issue with the output speed sensor on the vehicle's transmission lead frame. Under certain conditions, the transmission controls could force a temporary downshift into first gear. Depending on the speed of the vehicle at the time of the downshift, the driver could experience an abrupt speed reduction that could cause the rear tires to slide or lock up. This condition could result in loss of vehicle control, increasing the risk of a crash. Ford is aware of three reports of accidents and no injuries related to this condition. Affected vehicles are equipped with a 6R80 transmission and include certain 2011-2012 Ford F-150 vehicles built at Dearborn Truck Plant and Kansas City Assembly Plant, Aug. 19, 2011 through March 9, 2012; 2012 Ford Expedition vehicles built at Kentucky Truck Plant, Aug. 19, 2011 through Dec. 19, 2011; Ford Mustang vehicles built at Flat Rock Assembly Plant, Aug. 19, 2011 through Feb.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.