2012 Ford Fusion Sel, 3.0l V6, Leather, Ford Cpo 7yr/100k Warranty Included on 2040-cars

Auto blog

2014 Ford Fiesta ST priced from $21,400* [w/poll]

The 2014 model year brings a whole host of changes to Ford's Fiesta B-Segment fighter, the most important of which (to our enthusiast eyes, anyway) is the addition of a potent new ST model. The US-spec hot hatch was first shown at the 2012 Los Angeles Auto Show last November, and thanks to Ford's build-and-price site, we've now learned that the Fiesta ST will slide in at $21,400 when it goes on sale later this year (*not including $795 for destination).
Under the hood of the ST is a turbocharged 1.6-liter EcoBoost inline-four good for 197 horsepower and 214 pound-feet of torque, mated solely to a six-speed manual transmission. Ford hasn't released performance data on its pint-sized puncher just yet, but know that these numbers make the Fiesta ST ever-so-slightly more powerful than the larger Volkswagen GTI while returning an estimated 34 miles per gallon on the highway.
Elsewhere in the lineup, the standard Fiesta also gets a smattering of improvements for the 2014 model year, including a new 1.0-liter three-cylinder turbocharged engine and revised exterior styling. Pricing for the 2014 Fiesta sedan starts at $14,000, with the five-door model adding $600 to that number (again excluding the $795 destination fee).

New UAW boss Williams talks tough, vows 'no more concessions'

Dennis Williams, the newly elected president of the UAW, had some tough words for American automakers in his inauguration speech at the 2014 UAW Convention, striking down the possibility of any additional concessions from the 400,000-strong union.
"No more concessions. We are tired of it. Enough is enough," Williams said during his speech. UAW employees have not received a raise in nearly 10 years, according to Reuters.
Considering the recent strong results for Ford, Chrysler and General Motors, the union's demands are likely to carry a bit more weight in next year's negotiations. And considering Williams' tough stance, we could be in for some fireworks once negotiations commence.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).