2012 Ford F-350 Super Duty King Ranch Crew Cab Pickup 4-door 6.7l on 2040-cars

Auto blog

Ford offering factory-spec EcoBoost reflashes that don't void warranty*

Buy a supercharger or cold-air kit from Ford Racing and a Performance Calibration handset comes with it to reset the ECU for the upgrade. Now Ford Racing is offering the ProCal handset a la carte for $595, allowing you to reflash the ECU on your EcoBoost-equipped ride to extract more of its inherent capabilities without any additional upgrades. It gives you control of variables such as throttle response, idle speed and turbo wastegate control, among others. As for that warranty asterisk, the press release says enthusiasts can up the power "while maintaining the Ford-backed limited warranty." However Ford Motor Co. and Ford Racing are separate entities, and, best we can tell, when you reflash the ECU, your Ford warranty gets supplanted by the Ford Racing warranty. Say you bought a 2014 Ford, that means your five-year, 60,000-mile warranty becomes Ford Racing's three-year, 36,000-mile warranty, if we're reading the fine print correctly. If you have an older car and have driven more than 36,000 miles, then your warranty options are kaput, at least as far as a Ford in-house option. If have warranty concerns, you might also want to consider having a dealer perform the reflash, or at least ask about it. Once you've got past the small print, what about the numbers? At the moment Ford Racing offers tunes for the 2.0-liter EcoBoost in the Focus ST and the 1.6-liter EcoBoost in the Fiesta ST, and we're told there's a 90-pound-foot boost in torque at the crank after you've pressed the right buttons. Anecdotal evidence from a commenter at Road & Track says he went from 252 horsepower at the flywheel to 254 hp at the wheels, and 272 lb-ft at the flywheel to 354 lb-ft at the wheels, but we can't be sure that his adjustments were within Ford Racing specs. Your mileage, naturally, may vary. What about custom numbers for the 2.3-liter EcoBoost in the 2015 Ford Mustang? They aren't ready yet, but we're told we'll get something by the end of next year. Featured Gallery 2015 Ford Focus ST News Source: Ford, Ford Racing via Car and Driver Aftermarket Ford Technology ecoboost ford focus st ford fiesta st ford racing

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: