5.4l V8 Xl Fx4 4wd Lifted Fuel Rims Bedliner Power Windows Keyless Entry 4x4 on 2040-cars

Auto blog

Ford Fusion production scaled back just 3 months after it was accelerated

Three months after kicking off production of the Ford Fusion at its Flat Rock, MI factory, Ford Motor Company is taking steps to trim output in the face of heavily discounted competition from Toyota and a growing supply of vehicles.
The addition of Fusion production in Flat Rock - which also builds the Mustang - was meant to be what pushed the handsome mid-sizer past its arch-nemesis, the Toyota Camry. An extra facility building Fusions was also meant to curb the growing demand for Ford's highly profitable sedan.
But with word that Flat Rock would take "approximately" one extra week off for the holidays combined with an 88-day supply of Fusions - reportedly due in no small part to what Morgan Stanley analyst Adam Jonas called "aggressive discounting of the Camry" - some analysts are now beginning to wonder if Ford may have overextended itself by adding a second Fusion facility to the mix.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ring Brothers shows 1965-66 Mustang fastback carbon fiber body

We covered one of Ring Brothers' more extreme SEMA builds yesterday, the De Tomaso Pantera-based ADRNLN, but if that well-executed but over-the-top Italian-American exotic is too much for you, then perhaps this Ring Brothers 1965 Ford Mustang fastback with a carbon-fiber body suits your tastes better.
What the performance-parts manufacturer is showcasing with the Mustang is the carbon-fiber body itself, which is fashioned around the 1965-66 fastback. It can be bought from the company and bonded to the skin and unibody as a do-it-yourself project, or you can take your Mustang to Ring Brothers and have the body installed there. The fenders, doors and quarter panels are two-inches wider than stock, and Ring Brothers offers a custom widebody chassis to those who want the complete package.
The show car looks sharp in person lowered on HRE wheels, and we appreciate the bare front end so we can see the supercharged V8 and front coilover suspension, though the details on those performance upgrades are slim. Also note the custom independent rear suspension setup at the rear.