Find or Sell Used Cars, Trucks, and SUVs in USA

2012 Ford F-250 Super Duty Lariat Crew Cab Pickup 4-door 6.7l on 2040-cars

Year:2012 Mileage:9200
Location:

Fort Myers Beach, Florida, United States

Fort Myers Beach, Florida, United States

Wait until you get your eyes on this truck, Top of the line 6" Zone lift , Fule 22" split chrome polished black and Toyo 22" all terrain tires. This truck has 300 mi since lifted. WeatherTech floor mats and supper bed cover. Total cost of after market options $ 8000.00. Review the pictures, this truck just left the showroom, inside and out. Serious buyers only, I just dont use the truck but I love to look at it. Enjoy

Auto Services in Florida

Youngs` Automotive Service ★★★★★

Auto Repair & Service
Address: 1430 Ponce de Leon Blvd, Spring-Hill
Phone: (352) 796-3791

Winner Auto Center Inc ★★★★★

Auto Repair & Service, Auto Oil & Lube, Automobile Electric Service
Address: 3400 N Highway 1 (US 1), Cocoa
Phone: (321) 632-3175

Vehicles Four Sale Inc ★★★★★

Used Car Dealers
Address: 900 State St, Miami-Gardens
Phone: (954) 967-6988

Valvoline Instant Oil Change ★★★★★

Auto Repair & Service, Auto Oil & Lube, Automotive Tune Up Service
Address: 12890 W Colonial Dr, Oakland
Phone: (321) 236-5680

USA Auto Glass ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Windshield Repair
Address: Pembroke-Park
Phone: (954) 447-0031

Tuffy Auto Service Centers ★★★★★

Auto Repair & Service, Brake Repair
Address: 2572 Tamiami Trl, Port-Charlotte
Phone: (941) 764-9815

Auto blog

Ford family keeps special voting rights

Fri, 10 May 2013

Ford Motor Company has a dual-class stock structure of Class A and Class B shares. The roughly three billion Class A shares are for the general public like you and me, while the roughly 71 million Class B shares are all owned by the Ford family. Each Class A share gets the shareholder one vote, each Class B share is worth 16 votes, the result being that Common Stock holders control about 60 percent of the company while the Ford family controls 40 percent even though it holds far fewer shares. The only way that could ever change would be if the Fords sell their Class B shares, but even so, Class B shares revert to Class A when sold outside the family, so they'd have to sell a whole bunch of them.
A contingent of Class A shareholders think the dual-class system is unfair, and for the past few years a vote's been held during the annual shareholders meeting to end it. It has failed every time, as it just did again during the meeting held this week. A smidge over 33 percent voted to end the dual system, outvoted by the 67 percent who are happy with the way Ford is going - unsurprising in view of a corporate turnaround that will be part of business-class curricula for years to come.
On the sidelines, Ford elected Ellen R. Marram to the post of independent director, the first woman to hold the job. The former Tropicana CEO and 20-year Ford board member replaces retiring board member Irvine Hockaday who helped bring Alan Mulally to the CEO position.

Junkyard Gem: 1993 Mercury Topaz GS Sedan

Sat, Aug 13 2022

As long as the Mercury brand existed — a period spanning the 1939 through 2011 model years — nearly every Mercury sold in the United States was more or less a redecorated Ford model. The Torino had its Montego sibling, the Crown Victoria had the Grand Marquis, the Cougar was based on everything from the Mustang to the Mondeo, and so on. Naturally, when the folks in Dearborn developed the Ford Tempo compact, a Mercury version had to be created. This was the Topaz, with the official launch of both cars taking place on the deck of the aircraft carrier often referred to as the USS Decrepit. You can't make this stuff up! The Tempo/Topaz, also known as the Tempaz, has largely faded from our collective automotive memory by now, since it broke no significant new engineering or styling ground (this story would be much different if Ford had only put the amazing straight-eight "T-Drive" Tempaz powertrain into production) and didn't have any endearing features other than being a cheap domestic competitor to the Toyota Corolla and Nissan Sentra. Still, close to 3 million Tempazes left North American Ford and Lincoln-Mercury showrooms during the 1984-1994 period. As you'd expect, most of these disposable cars disappeared from both the street and the car graveyard long ago. It takes a very special Tempaz for me to break out my camera while I'm patrolling my local wrecking yards; generally, this means an ultra-rare all-wheel-drive version or at least a very early model in super-clean condition. Today's Junkyard Gem is neither, but I took one look at this spectacular Bordello Red crypto-velour-and-slippery-plastic interior and recognized that this was no ordinary junkyard Mercury. It appears that Mercury had dropped the idea of clever names for base-grade seat fabrics by the time of the Topaz, referring to this stuff as just "cloth" in all the brochures I could find. That's too bad, because Mercurys had cool names for upholstery (e.g., Chromatex) in the old days. The interior is in very good condition but the steering wheel shows substantial wear, so I think this is a high-mile Topaz that got meticulous care from its owner or owners. Ford used five-digit odometers on these cars until the end of production, however, so we'll never know if this reading indicates 65,404 miles or 365,404 miles. The body is very straight, but there's some nasty corrosion behind the right front wheelwell.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Thu, 13 Feb 2014

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.