We Finance!!! 2010 Ford F-150 Lariat 4x4 Flex-fuel Roof Nav Rcam Sync 20 Rims! on 2040-cars

Auto blog

Ford recalls 1.9m cars and crossovers for defective airbags

The Basics: Ford is recalling a total of 1,898,728 vehicles to replace defective Takata front passenger-side airbags. This includes the 2007-2010 Ford Edge, 2006-2011 Ford Fusion, 2005-2011 Ford Mustang, 2007-2011 Ford Ranger, 2007-2010 Lincoln MKX and 2006-2011 Lincoln MKZ, Zephyr and Mercury Milan vehicles built in North America. The Problem: The defective airbags have been linked to ruptures that can send metal fragments at the passenger, due to deteriorating propellant. Injuries/Deaths: Ford claims it's not aware of any injuries due to the problem, but rupturing Takata airbags have been linked to a series of serious injuries and deaths. The Fix: Dealers will replace the passenger-side frontal airbag at no charge to the customer. If you own one: Look out for a letter from the manufacturer to arrange service at your local dealer. If you'd like to check if your vehicle is affected, click on the safety recalls link on Ford.com and enter your VIN. Related Video:

Ford finally issues recall for 230K minivans over rust problems

The rust issue in the rear wheel wells of 2004-2007 Ford Freestar and Mercury Monterey minivans has finally led to a recall. The National Highway Traffic Safety Administration began an investigation into the matter in 2011, said investigation being upgraded to an engineering analysis a year later while NHTSA tried to figure out how many model years should be included in the assessment.
Ford has decided to recall all of the 230,000 minivans potentially affected, namely those sold in salt-belt states and countries like Canada. The excess rust in the rear wheel wells was also able to prevent the third-row seats from locking to the floor of the minivan. To repair the problem, owners can take their minivans to dealers, and the dealers will place new panels in the wheel wells, replace the third-row seat mounting brackets and relocate the latches to an area away from any corrosion.
Ford says it will begin notifying owners during the last week of March.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).