2011 Ford F-150 on 2040-cars

Auto blog

2014 Ford Fiesta ST

I'm not overly inclined to professional jealousy, as a rule. Sure, I go a bit green around the eyes when Ramsey draws the 911 GT3 trip to Weissach, Harley is tapped-in to drive a completely stunning Porsche 911 by Singer, or, you know, Drew Phillips gets to shoot a Lamborghini Veneno in the middle of a desert like some sort of sheik. I hate you guys...
Honestly though, one of the new car events that dug me the most, was when our Steven J. Ewing got to fling the Ford Fiesta ST around some hot corner of Europe. What goes around comes around, I suppose, as Mr. Ewing himself espoused an envious nature of the Focus ST trip that came before.
The good news in all this covetous intra-office behavior? All the cars mentioned, and specifically the Fiesta ST, are just wonderful to drive. I can say that with more confidence than ever now, having joined Ford for a good bit of Fiesta-flinging myself. In my case, the locale was slightly more pedestrian (Michigan not Portugal), and the car in question was the five-door version of the Fiesta ST that we get here in The States, as opposed to the three-door number they get across the pond.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

2014 Ford Transit unveiled in Chassis Cab and Cutaway versions

As a leader in commercial vehicles here in the US, we knew Ford wouldn't take too long to show off the chassis cab and cutaway versions of its 2014 Ford Transit van. Set to go on sale this fall, Ford already revealed the full-body version of the Transit, and now it has pulled the cover off exposed-frame models just in time to to compete against the all-new Ram Promaster.
The term "chassis cab" refers to models with a fully enclosed cabin used for box vans or rental trucks, while cutaway models leave the cabin open behind the B-pillars for a pass-through on vehicles such as Class C motorhomes or ambulances. Both will offer three wheelbase options (138, 156 and 178 inches), the choice of single or dually rear axles, and plenty of upfitter-friendly touches including a pre-wired body harness and multiple body mount locations.
The new design will also help make upfitting a little easier since the fuel filler is now built into the cab (just behind the driver's door). Those integrated fuel filler necks will serve to feed either a 3.7-liter V6, a 3.5-liter EcoBoost V6, or a 3.2-liter Power Stroke diesel. Transit chassis cab and cutaways will wear varying Gross vehicle weight ratings from 9,000 pounds to 10,360 pounds depending on spec.